Manuel d'utilisation / d'entretien du produit JD 5093E du fabricant Tiger Products Co., Ltd
Aller à la page of 182
P AR TS LISTING WITH MOUNTING AND OPERA TING INSTRUCTIONS CHEET AH BOOM ASSEMBLIES JD 5101E, 5093E & 5083E UP THROUGH SERIAL #’s L V5101E260403 L V5093E260318 L V5083E260784 06010005 Tiger Corporation 3301 N. Louise Ave. Sioux Falls, SD 57107 1-800-843-6849 1-605-336-7900 www .
T O THE OWNER / OPERA TOR / DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices.
FOR W ARD This manual contains information about many features of the T iger mowing and roadside maintenance equipment. Some of these include: Safety precautions, Assembly instructions, Operations, Maintenance and Parts. This manual will also assist you in the proper break-in, daily care, and troubleshooting of your new mower .
.
T ABLE OF CONTENTS SAFETY _____________________________________________ 1-1 Safety Information__________________________________ 1-2 ASSEMBL Y / MOUNTING SECTION _______________________ 2-1 OPERA TION.
.
Cheetah Safety Section 1-1 SAFETY SAFETY SECTION.
Cheetah Safety Section 1-2 SAFETY Indicates an imminently hazardous situation that, if not avoided, WILL result in DEA TH OR VERY SERIOUS INJURY . Indicates an imminently hazardous situation that, if not avoided, COULD result in DEA TH OR SERIOUS INJUR Y .
Cheetah Safety Section 1-3 SAFETY DANGER! Never operate the Tractor or Implement until you have read and completely understand this Manual, the Tractor Operator’s Manual, and each of the Safety Messages found in the Manual or on the Tractor and Implement.
Cheetah Safety Section 1-4 SAFETY DANGER! Never allow children or other persons to ride on the Tractor or Implement. Falling off can result in serious injury or death. (SG-10) DANGER! Never allow children to operate or ride on the Tractor or Implement.
Cheetah Safety Section 1-5 SAFETY WARNING! T ransport only at safe speeds. Serious accidents and injuries can result from operating this equipment at unsafe speeds. Understand the T ractor and Implement and how it handles before transporting on streets and highways.
Cheetah Safety Section 1-6 SAFETY WARNING! Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion or while tractor engine is running.
Cheetah Safety Section 1-7 SAFETY DANGER! NEVER use drugs or alcohol immediately before or while operating the Tractor and Implement. Drugs and alcohol will affect an operator’s alertness and coordination and therefore affect the operator’s ability t o operate the equipment safely.
Cheetah Safety Section 1-8 SAFETY WARNING! Extreme care should be taken when operating near loose objects such as gravel, rocks, wire, and other debris. Inspect the area before mowing. Foreign objects should be removed from the site to prevent machine damage and/or bodily injury or even death.
Cheetah Safety Section 1-9 SAFETY WARNING! Do not mow with two machines in the same area except with Cab tractors with the windows closed. (SGM-11) DANGER! Rotary and Flail Mowers are capable under adverse conditions of throwing objects for great distances (100 yards or more) and causing serious injury or death.
Cheetah Safety Section 1-10 SAFETY Relieve hydraulic pressure prior to doing any maintenance or repair work on the Implement. Place the Mower Head on the ground or securely supported on blocks or stands, disengage the PTO, and turn off the engine.
Cheetah Safety Section 1-11 SAFETY WARNING! In addition to the design and configuration of this Implement, including Safety Signs and Safety Equipment, hazard control and accident prevention are depen.
Cheetah Safety Section 1-12 SAFETY ITEM PART NO. QTY. DESCRIPTION 33514 AVAIL DECAL KIT CHEETAH TRACTOR 1 33302 1 JOYSTICK OPERA TION (CAB) 1 34206 1 LEVER OPERA TION (NON CAB) 2 22645 1 PO L YCARBONA TE WINDOW 3 02962764 6 W ARNING , PINCH POINT 5 33436 1 DECAL, CHEET AH 10 6T3236 1 DECAL, MADE IN U.
Cheetah Safety Section 1-13 SAFETY ITEM PART NO. QTY. DESCRIPTION 33439 AVAIL DECAL KIT CHEETAH ROTARY 4 22839 1 CAUTION, HAND GREASE ONL Y 5 33436 2 DECAL, CHEET AH 6 TB101 1 2 W ARNING , DO NOT REMO.
Cheetah Safety Section 1-14 SAFETY ITEM PART NO. QTY. DESCRIPTION 33786 AVAIL DECAL KIT CHEETAH FLAIL 1 6T3261 2 CAUTION LUBE INSTRUCTIONS 2 42350 1 DECAL, ROT A TION, CUTTERSHAFT 3 6T3249A 2 DECAL, C.
Cheetah Safety Section 1-15 SAFETY 00769737 00725746 002369.
Cheetah Safety Section 1-16 SAFETY 02962764 02962765 02965262.
Cheetah Safety Section 1-17 SAFETY 22839 02971 123 03200285 22645.
Cheetah Safety Section 1-18 SAFETY 22840 24028 25387.
Cheetah Safety Section 1-19 SAFETY 32707 32708 32709.
Cheetah Safety Section 1-20 SAFETY 33224 33302 33435.
Cheetah Safety Section 1-21 SAFETY RED 42399 33436 33437 33438 42350.
Cheetah Safety Section 1-22 SAFETY AMBER 42400 6T3217 6T3219 6T3220 6T3221.
Cheetah Safety Section 1-23 SAFETY 6T3230 6T3233 6T3222 6T3224 6T3225.
Cheetah Safety Section 1-24 SAFETY 6T3234 6T3236 6T3237 34206.
Cheetah Safety Section 1-25 SAFETY 33743 6T3243 TB101 1.
Cheetah Safety Section 1-26 SAFETY 34852 HYDRAULIC T ANK.
Cheetah Safety Section 1-27 SAFETY ITEM PART NO. QTY. DESCRIPTION 50023 AVAIL MANUAL CANISTER COMPLETE 1 00776031 1 ROUND MANUAL CANISTER 33997 1 DECAL, SHEET, MANUAL CANISTER 2 * DECAL 3 * DECAL 4 * .
Cheetah Safety Section 1-28 SAFETY This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators. This section is not intended as a legal interpretation of the law and should not be considered as such .
ASSEMBL Y SECTION Assembly Section 2-1.
Assembly Section 2-2 ASSEMBL Y Before attempting to mount or service your Tiger mower , it is import ant to read and understand all of the information in the Safety section of this manual. Check complete shipment list against the packing list to make sure there are no shortages.
Assembly Section 2-3 ASSEMBL Y MAIN FRAME MOUNTING It may be necessary to raise the front of the tractor slightly to allow the main frame to be slid under the tractor . With an overhead hoist or floor jack, slide the frame under the tractor from the right hand side.
Assembly Section 2-4 ASSEMBL Y 3-POINT BOOM REST MOUNTING Before installing the rear boom rest onto the 3-point hitch, you must set the 3- point stop lever (to the right of the seat) to setting “4” and lock into position as shown below . (See tractor owners manual for further instruction on use of the 3-point hitch stops.
Assembly Section 2-5 ASSEMBL Y JOYSTICK SWITCH BOX MOUNTING Locate the 2 existing threaded holes in the right front corner of the cab frame. These will be the mounting holes for the 2 mounting bolts of the switch box bracket. See picture below . Mount the bracket using the hardware supplied, as noted in the parts section.
Assembly Section 2-6 ASSEMBL Y JOYSTICK SWITCH BOX WIRING Refer to the parts section for the danfoss wiring schematic to hook up the switch box. Cover all wires with plastic wire wrap provided. Route the green wires along switch box bracket and cab frame to the steering wheel console.
Assembly Section 2-7 ASSEMBL Y JOYSTICK CONTROL MOUNTING The joystick is mounted to the right hand center cab post. Find the two existing bolts above the area where the post bumps out. See the image below . Mount the joystick mounting bracket to the cab post with hardware provided.
Assembly Section 2-8 ASSEMBL Y DANFOSS V AL VE PLUMBING (SCV ONL Y UNITS) A priority valve will be used to power the danfoss valve. The tractor ports used are on the selective control valve (SCV). The SCV is located between the right arm of the three point hitch and the axle.
Assembly Section 2-9 ASSEMBL Y DANFOSS V AL VE PLUMBING (WITH MID-MOUNT V AL VE) A priority valve will be used to power the danfoss lift valve. The tractor ports used are on the selective control valve (SCV) and the Mid-Mount V alve. The SCV is located between the right arm of the three point hitch and the axle.
Assembly Section 2-10 ASSEMBL Y HUSCO V AL VE PLUMBING (SCV ONL Y UNITS) The tractor ports used are on the selective control valve (SCV). The SCV is located between the right arm of the three point hitch and the axle. The pressure port is located the closest to the axle.
Assembly Section 2-11 ASSEMBL Y HUSCO V AL VE PLUMBING (WITH MID-MOUNT V AL VE) The tractor ports used are on the selective control valve (SCV) and the Mid-Mount valve. The SCV is located between the right arm of the three point hitch and the axle. The Mid-Mount valve is located under the right front corner of the cab.
Assembly Section 2-12 ASSEMBL Y CABLE CONTROL LEVER ST AND (SCV ONL Y UNITS) Place the cable control bracket on the floor so that the bracket is 1-1/4” from the right corner post of the cab and the edge of the door opening. Also the outer rear corner of the bracket is 3 3/4” from the edge of the door .
Assembly Section 2-13 ASSEMBL Y The rubber boot in the corner of the rear window can be cut in a cross hair pattern and if necessary the bottom cut through to allow it to slip over the cables and back into position.
Assembly Section 2-14 ASSEMBL Y HOSE AND CABLE ROUTING Attach two clamps to the right rear wheel well for proper hose/cable routing. Drill one hole for each clamp. Use the lower rear corner of the wheel well as an origin for measuring. The holes should be 10mm or 3/8” reamed to accept 3/8” hardware.
Assembly Section 2-15 ASSEMBL Y.
Assembly Section 2-16 ASSEMBL Y CHEET AH HOSE ROUTING W ARNING NOTE: The sudden release of hydraulic pressure could cause the sudden movement of very heavy part s.
Assembly Section 2-17 ASSEMBL Y Arrange the hoses in the clamp that attaches to the boom mounting bracket as shown above, with the 1” motor hoses closest to the bracket and the return hose closest to the boom arm.
Assembly Section 2-18 ASSEMBL Y HYDRAULIC T ANK INST ALLA TION Attach the tank mount to the main frame with the hardware shown in the parts section. Install all fittings and tubes into tank and tank filter as shown in parts section illustration. Insert tank sight glass into front side of the tank.
Assembly Section 2-19 ASSEMBL Y DECK A TT ACHMENT Attach the head to the secondary boom using the pins and hardware shown in the parts section to attach linkages. Install the square tube on the top of the head into the head mount and secure using the mounting plate and hardware as shown.
Assembly Section 2-20 ASSEMBL Y WHEEL WEIGHT MOUNTING For all machines using a boom mower , a wheel weight will be required for the left side wheel. It will be necessary to mount the 500 pound wheel weight in the wheel using the long cap-screws, lock-washers, flat-washers, and hex nuts per diagram in the parts section.
Assembly Section 2-21 ASSEMBL Y BOOM JOYSTICK CONTROL CALIBRA TION SUB-D This Danfoss PVG32 control valve is now equipped with higher-resolution actuators on Main Boom, Secondary Boom, Deck Roll, and Swivel functions. These actuators have “active fault monitoring”.
Assembly Section 2-22 ASSEMBL Y Run tractor at normal operating RPM to adjust the settings as follows. Set the dead band compensation potentiometer first. Set the dead band compensation potentiometer at 50%, or halfway between full clockwise and full counter-clockwise.
Assembly Section 2-23 ASSEMBL Y MAIN BOOM: “A” Port, Boom UP: 7-9 Seconds (Note: Extend secondary boom completely; roll deck to be level with ground, and lower main boom until deck is on ground. Now index main boom “up” function and determine the time required for main boom to rise completely .
Assembly Section 2-24 ASSEMBL Y.
Assembly Section 2-25 ASSEMBL Y FINAL PREP ARA TION FOR OPERA TION Place operators safety and operation decals on the steering column and side console where they are clearly visible to the operator . These decals should be understood by each operator of the machine in conjunction with the safety and operation section of this book.
Assembly Section 2-26 ASSEMBL Y 4WD FRONT TIRE ADJUSTMENT In order to prevent interference with mounted equipment, the front wheels on a 4WD 5101E tractor will have to be adjusted to approximately 64” center to center distance as shown below .
Cheetah Operation Section 3-1 OPERA TION OPERA TION SECTION.
Cheetah Operation Section 3-2 OPERA TION Safety is of primary importance to the owner / operator and to the manufacturer . The first section of this manual includes a list of Safety Messages , that, if followed, will help protect the operator and bystanders from injury or death.
Cheetah Operation Section 3-3 OPERA TION ST ARTING TRACT OR AND MOWER Check the operators manual received from the tractor manufacturer , for their recommendation and procedures pertaining to your particular make and model. When rotating parts are in motion, serious injury may occur if caution is not used or danger is not recognized.
Cheetah Operation Section 3-4 OPERA TION The Mower Control switch turns the mower “ON” and “OFF . This switch is to be in the “OFF” position to start the tractor . If the switch is “ON” and the tractor ignition switch is turned to “ON” the red “mower run” indicator light will come on.
Cheetah Operation Section 3-5 OPERA TION The Safety Shield switch opens and closes the shield located on the front of the cutter head. When mowing at or near the ground, always have the shield in the closed position. When mowing in brush or in trees above ground level the shield may be opened for easier cutting.
Cheetah Operation Section 3-6 OPERA TION JOYSTICK CONTROL The diagrams below and on page 3-6 show the functions that are performed through the use of the joystick controller .
Cheetah Operation Section 3-7 OPERA TION JOYSTICK FWD / BACK MOVES MAIN BOOM JOYSTICK LEFT / RIGHT MOVES SECONDAR Y BOOM LEFT JOYSTICK ROLLER MOVES DECK ROLL RIGHT JOYSTICK ROLLER MOVES BOOM SWIVEL SH.
Cheetah Operation Section 3-8 OPERA TION The main control valve on the T iger Boom Mower has four sections with tapered spools, located near the right side of the steering wheel. The malfunction of a section of the valve does not necessitate the replacement of the entire “bank”, only the faulty section.
Cheetah Operation Section 3-9 OPERA TION LEVER #1 MOVES MAIN BOOM LEVER #2 MOVES SECONDAR Y BOOM LEVER #3 MOVES DECK ROLL LEVER #4 MOVES BOOM SWIVEL LEVER #5 OPERA TES SAFETY SHIELD.
Cheetah Operation Section 3-10 OPERA TION MOWER OPERA TION When rotating parts are in motion, serious injury may occur if caution is not used or danger is not recognized. Never allow bystanders within 300 feet of the machine when in operation. Extreme care should be taken when operating near loose objects – such as gravel, rocks and debris.
Cheetah Operation Section 3-11 OPERA TION The mower will operate more efficiently in tougher conditions and with less power if the knives are kept sharp. If the mower begins to vibrate, stop the tractor , check for wire wrapped in the spindle or damaged knives.
Cheetah Operation Section 3-12 OPERA TION TRANSPORTING MOWER T ransporting under the units own power: When transporting between job sites, the following procedure should be followed: Shut off the power to the cutting head and allow all motion to come to a complete stop.
Cheetah Operation Section 3-13 OPERA TION T ransporting unit by flatbed trailer: Park flatbed on level area. Drive tractor onto center of flatbed to avoid uneven distribution of weight and staying within local width restrictions.
Cheetah Operation Section 3-14 OPERA TION INSPECTION SHEETS.
Cheetah Operation Section 3-15 OPERA TION BOOM MOWER PRE-OPERA TION Inspection Mower ID#_____________ Make___________________ Date:__________________ Shift____________________ Before conducting the inspection, make sur e the T ractor engine is off, all rotation has stop and the tractor is in the Park with the parking brake engaged.
Cheetah Operation Section 3-16 OPERA TION TRACT OR PRE-OPERA TION Inspection T ractor ID#____________ Make_____________________ Date:__________________ Shift______________________ Before conducting the inspection, make sur e the T ractor engine is of f, all rotation has stop and the tractor is in the Park with the parking brake engaged.
Cheetah Operation Section 3-17 OPERA TION FRONT END LOADER PRE-OPERA TION Inspection Mower ID#_____________ Make___________________ Date:__________________ Shift____________________ Before conducting the inspection, make sur e the T ractor engine is off, all rotation has stop and the tractor is in the Park with the parking brake engaged.
Cheetah Operation Section 3-18 OPERA TION TRACT OR PRE-OPERA TION Inspection T ractor ID#____________ Make_____________________ Date:__________________ Shift______________________ Before conducting the inspection, make sur e the T ractor engine is off, all rotation has stop and the tractor is in the Park with the parking brake engaged.
MAINTENANCE SECTION Cheetah Maintenance Section 4-1.
Cheetah Maintenance Section 4-2 MAINTENANCE T iger Mowers are designed for high performance and rugged durability , yet with simplified maintenance. The purpose of this section of the manual is to help the operator in the regular servicing of the mower .
Cheetah Maintenance Section 4-3 MAINTENANCE REGULAR MAINTENANCE The intervals at which regular servicing should be done are based on hours of operation. Use the tractors hour meter to determine when regular servicing is required. This symbol indicates a point that needs to be greased at an interval noted in the section below .
Cheetah Maintenance Section 4-4 MAINTENANCE WEEKL Y OR EVER Y 50 HOURS ITEM SERVICE COMMENTS In T ank Hyd. Fluid Filter Change Change after the first 50 hours only , (10 micron filter) then every 500 hours, yearly or if indicated by the restriction indicator .
Cheetah Maintenance Section 4-5 MAINTENANCE SYMPTOMS CAUSE REMEDY Mower will not start 1. Electronic 1a. Without the tractor running, turn or run, cont. solenoid faulty the mower switch to on. A low audible click should be heard if the solenoid is engaging the solenoid spool.
Cheetah Maintenance Section 4-6 MAINTENANCE T ORQUE SPECIFICA TIONS * These are intended to be general specifications. See tractor operators or service manual for exact specifications for your tractor parts.
Cheetah Maintenance Section 4-7 MAINTENANCE LUBRICA TION RECOMMENDA TIONS Description Application General Specification Recomended Mobil Lubricant T ractor Hydraulics Reservoir JD-20C Mobilfluid 424 M.
Cheetah Maintenance Section 4-8 MAINTENANCE POL YCARBONA TE CARE & MAINTENANCE The proprietary UV and Abrasion Resistant surface coating on SHIELDS ® SUPERCOA TED ™ polycarbonate significantly improves performance. Periodic cleaning using proper procedures and compatible cleaners are recommended to prolong service life.
Cheetah Maintenance Section 4-9 MAINTENANCE DET AILED MAINTENANCE REPLACING IN-T ANK HYDRAULIC FIL TER: Loosen the four bolts on the top cover of the filter housing.
Cheetah Maintenance Section 4-10 MAINTENANCE DET AILED MAINTENANCE REPLACEING HIGH PRESSURE HYDRAULIC FIL TER ELEMENT : Assure system has been shut down and de-pressurized. Locate High Pressure Filter housing. Confirm that the element that is about to be installed matches the element p/n on the filter model tag.
Cheetah Maintenance Section 4-11 MAINTENANCE GREASING SPINDLE Locate grease fitting on inside of deck housing. Inject T iger S pindle Lubricant, part number 06540000 into spindle housing. Fill with lubricant until lubricant weeps out of the top spindle seal.
Cheetah Maintenance Section 4-12 MAINTENANCE TIGHTENING SPINDLE BOL TS The spindle mounting bolts should be checked and retorqued daily or every 8 hours of service as follows: T orque the (6) bolts shown below to 357 f t.
Cheetah Maintenance Section 4-13 MAINTENANCE GREASING THE BOOM SWIVEL Locate the zerks on the main swivel boss (2), main boom pivot boss (2) and on both ends of the boom swivel cylinder . Inject Lithium-Complex Extreme Pressure grease conforming to NLGI2-ISO 320 specifications until grease begins to protrude from ends.
Cheetah Maintenance Section 4-14 MAINTENANCE BALL V AL VES The ball valve at the hydraulic reservoir may need to be closed during certain maintenance or repair procedures. THE BALL V AL VES MUST BE OPEN (handle p arallel with valve) WHEN TRACTOR IS RE-ST ARTED OR PUMP IS COUPLED TO MOTOR OR P .
Cheetah Maintenance Section 4-15 MAINTENANCE BOOM FLAIL KNIFE REPLACEMENT 1 – If knives are damaged or badly worn, they will need to be replaced as a set. Replacing a single knife can cause severe vibration and possible damage to the mower . 2 – Assemble knives, bushings, collars, bolts and nuts as shown in p art section of manual.
Cheetah Maintenance Section 4-16 MAINTENANCE CHEET AH SPINDLE ASSEMBL Y INST ALLA TION AND BEARING ADJUSTMENT W ARNING! A press MUST be used to install bearing cup s, bearing cones, and seals. DO NOT use a hammer to install races, bearings, or seals. The parts of assembly may be damaged.
Cheetah Maintenance Section 4-17 MAINTENANCE BEARING INST ALLA TION 1 – Press upper bearing cup into the spindle housing. 2 – T urn the spindle housing over and press in the lower bearing cup. 3 – Place the lower bearing cone in the bearing cup.
Cheetah Maintenance Section 4-18 MAINTENANCE BEARING ADJUSTMENT 1 – Clamp the bottom end of the spindle securely in a vise so the spindle housing turns freely . 2 – Position a magnetic base dial indicator on the outer diameter of the spindle housing.
Cheetah Maintenance Section 4-19 MAINTENANCE DAIL Y MAINTENANCE SCHEDULE The following services should be performed daily or every 8 hours of service, following the detailed maintenance instructions in the operators manual. ______ Pump Drive Shaft: Check for end play in drive shaft / coupler and lubricate zerk on coupler .
Cheetah Maintenance Section 4-20 MAINTENANCE.
P ARTS SECTION JD 5101E - CHEET AH BOOM MOWER Parts Section 5-1.
Parts Section 5-2 The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this manual. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual.
Parts Section 5-3 P ARTS SECTION T ABLE OF CONTENTS SECTION ASSEMBL Y P AGE TRACTOR SPECIFIC P ARTS: TRACTOR MNT . KIT - MAIN FRAME, 5101E 06101775 5-4 TRACTOR MOUNT KIT - HYDRAULICS 06101775 5-6 TRACTOR MNT .
Parts Section 5-4 TRACTOR MOUNT KIT - MAIN FRAME 5101E.
Parts Section 5-5 TRACTOR MOUNT KIT - MAIN FRAME 5101E ITEM PART NO. QTY. DESCRIPTION 1 06300033 1 MNFRM,JD5525,CHET ,TSF/TM 2 06300035 1 AXLE BRACE,RIGHT HAND 3 06300088 1 MOUNT , T ANK 4 32642 1 PUM.
Parts Section 5-6 TRACTOR MOUNT KIT - HYDRAULICS 5101E.
Parts Section 5-7 TRACTOR MOUNT KIT - HYDRAULICS 5101E ITEM PART NO. QTY. DESCRIPTION 1 06300033 1 MAIN FRAME 2 06300088 1 MNT ,HTDRO T ANK,NHT6010 3 06700090 ASSY HYDRAULIC T ANK 4 23152 1 P U M P 5 .
Parts Section 5-8 TRACTOR MOUNT KIT - MAIN FRAME 5101E - LOADER.
Parts Section 5-9 TRACTOR MOUNT KIT - MAIN FRAME 5101E - LOADER ITEM PART NO. QTY. DESCRIPTION * 06700091 A V AIL. T ANK,RES,ASSY ,WHEEL WELL 1 06380015 1 T ANK,RES,WHEEL WELL 2 06505044 1 F I L TER A.
Parts Section 5-10 TRACTOR MOUNT KIT - HYDRAULICS 5101E - LOADER.
Parts Section 5-11 TRACTOR MOUNT KIT - HYDRAULICS 5101E - LOADER ITEM PART NO. QTY. DESCRIPTION 1 * R E F REFER TO MAIN FRAME P ARTS 2 06506012 2 PRFRMD TUBE 3 33555 4 ADAPTER,1MORBX1MJIC 4 * R E F RE.
Parts Section 5-12 TRACT OR MOUNT KIT - WHEEL WELL T ANK.
Parts Section 5-13 TRACTOR MOUNT KIT - WHEEL WELL T ANK ITEM PART NO. QTY. DESCRIPTION * 06700091 A V AIL. T ANK,RES,ASSY ,WHEEL WELL 1 06380015 1 T ANK,RES,WHEEL WELL 2 06505044 1 FIL TER ASSY ,IN-T .
Parts Section 5-14 TRACTOR MOUNT KIT - HYDRO, WHEEL WELL T ANK.
Parts Section 5-15 TRACTOR MOUNT KIT - HYDRO, WHEEL WELL T ANK ITEM PART NO. QTY. DESCRIPTION 1 06300033 1 MAIN FRAME 2* 1 1” HOSE 3* 1 1” HOSE 4 33555 2 ADAPTER,1MORB x 1MJIC 5 * R E F BRAKE V AL.
Parts Section 5-16 BOOM MOUNT KIT - BOOM SWIVEL / BOOM REST.
Parts Section 5-17 BOOM MOUNT KIT - BOOM SWIVEL / BOOM REST ITEM PART NO. QTY. DESCRIPTION 1 06310023 1 BOOMREST ,STD,3PNT 2 06310030 1 M N T BRKT ,BOOM,GREASELESS,CHET 3 06700056 1 SWIVEL,ASSY ,GREASELESS,CHET 4 34275 1 CYL,2 1/2X1 1 1/2,2500 PSI 5 06420013 1 PIN,1.
Parts Section 5-18 SWITCH BOX AND JOYSTICK 5101E.
Parts Section 5-19 ITEM PART NO. QTY. DESCRIPTION 1 06340031 1 MT ,BRKT ,JYSTK,JD5101E 2 33691 1 JOYST ,4AXIS,RH,DF ,W/SUB-D CONN 3 06770022 1 CAN,JYSTK,TRUCKA T ,4WD 4 06520019 2 MOUNT ,RAM BALL,1 1/.
Parts Section 5-20 LIFT V AL VE - JOYSTICK CONTROL.
Parts Section 5-21 LIFT V AL VE - JOYSTICK CONTROL ITEM PART NO. QTY. DESCRIPTION 1 06502095 1 V A L VE,5SP ,DANFOSS 2 06340017 1 V A LVE M N T 3 34622 1 P L A TE,V AL VE,REAR MNT 4 06502102 1 V A L V.
Parts Section 5-22 CABLE CONTROLS - SCV ONL Y ITEM PART NO. QTY. DESCRIPTION 1 23865B 1 CBL CTRL MT BRK,9030-FD40-JD60 2 6T1251 3 CBL CTRL BOX,180 DEG 3 06510100 1 SWITCHBOX,BOOM 4 34496 1 BRKT ,SWITC.
Parts Section 5-23 CABLE CONTROLS - WITH MID-MOUNT V AL VE ITEM PART NO. QTY. DESCRIPTION 1 31923 1 BRKT ,CTRL,CBL,JD52-5500,CAB, 2 6T1251 5 CBL CTRL BOX,180 DEG 3 06510100 1 SWITCHBOX,BOOM 4 34496 1 .
Parts Section 5-24 LIFT V AL VE - CABLE CONTROL, CAB.
Parts Section 5-25 LIFT V AL VE - CABLE CONTROL, CAB ITEM PART NO. QTY. DESCRIPTION 1 33500 1 V AL VE,5SP ,HSC,TRB,PB 2 06340017 1 V A LVE M N T 3 34622 1 P L A TE,V AL VE,REAR MNT 4 21632 9 CAPSCREW .
Parts Section 5-26 ITEM PART NO. QTY. DESCRIPTION 1 06490014 1 POLYCARB, FRMD, REAR 2 06490013 1 POLYCARB, FRMD, DOOR 3 31965 2 5 ’ TRIM SEAL 4 21584 2 CAPSCREW, 5/16” X 2” 5 21575 6 HEX NUT, 5/.
Parts Section 5-27 SOLENOID V AL VE SWITCH AND WIRING 1 * REF SWITCH BOX 2 RE37651 1 PLUG ,AUX PWR 3 24204 OP T . FUSE HOLDER,IN-LINE 4 6T3965 OP T . FUSE,3AMP 5 6T3934 O PT . TEMPERA TURE GAUGE 6 6T3931 OP T . TEMPERA TURE SENSOR ITEM P ART NO. QTY .
Parts Section 5-28 WHEEL SP ACER ITEM P ART NO. QTY . DESCRIPTION 1 06770025 1 KIT ,SPCR,WHL,JD 2 06400919 2 RING ,SP ACER,WHEEL,JD.
Parts Section 5-29 WHEEL WEIGHT ASSEMBL Y ITEM PART NO. QTY. DESCRIPTION 1 30687 1 500# WHEEL WEIGHT 2 21956 4 CAPSCREW - 3/4 X 13 3 33626 8 FLATWASHER - 3/4 4 TB3278 4 SPACER 5 21993 4 LOCKWASHER - 3.
Parts Section 5-30.
COMMON P ARTS SECTION CHEET AH BOOM MOWER.
Cheetah Common Section 6-2 The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this manual. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual.
Cheetah Common Section 6-3 P ARTS SECTION T ABLE OF CONTENTS SECTION P A G E TRACTOR SPECIFIC P ARTS: CHEETAH QUICK COUPLERS 6-4 CHEETAH BOOM ARM ASSY 6-6 CHEETAH ROTARY MOWER DECK 6-8 CHEET AH ROT AR Y PIVOT ASSY . 6-10 DAN FOSS V AL VE BREAKDOWN 6-12 HUSCO V AL VE BREAKDOWN 6-14 CHEET AH ROT AR Y MOT OR 6-20 ROT ARY SPINDLE ASSY .
Cheetah Common Section 6-4 CHEET AH QUICK COUPLERS - MAIN BOOM.
Cheetah Common Section 6-5 CHEET AH QUICK COUPLERS - MAIN BOOM ITEM PART NO. QTY. DESCRIPTION 1 34392 2 ADAPTER,1ORB X 1FJX 2 06503027 2 QUICK COUPLER,1”SAE,FEMALE 3 06503028 2 QUCK COUPLER,1”SAE,MALE 4 33555 2 ADAPTER,1MORB X 1MJIC 5 * REF. PREFORMED TUBES - REFER TO BOOM ARM PARTS 6 * REF.
Cheetah Common Section 6-6 CHEET AH BOOM ARM ASSEMBL Y.
Cheetah Common Section 6-7 ITEM PART NO. QTY. DESCRIPTION 1 31153A 1 MAIN BOOM ARM 2 31154A 1 SECONDARY BOOM ARM 3 33702 1 CYLINDER 4 33703 1 CYLINDER 5 33731 1 CYLINDER 6 23888 1 ACCUMULATOR BRACKET .
Cheetah Common Section 6-8 CHEET AH ROT AR Y MOWER DECK.
Cheetah Common Section 6-9 ITEM PART NO. QTY. DESCRIPTION 33425 AVAIL. CHEETAH ROTARY HEAD,COMPLETE ASSY. 1 32974 1 CHEETAH ROTARY DECK 2 32977 1 SHEILD 3 06504012 1 MOTOR 4 TF4852 2 FLANGE KIT 5 3343.
Cheetah Common Section 6-10 CHEET AH ROT AR Y PIVOT ASY ..
Cheetah Common Section 6-11 CHEET AH ROT AR Y PIVOT ASY . ITEM PART NO. QTY. DESCRIPTION 1 31267 1 PIVOT WELDMENT 2 33523 1 PIVOT LINK 2 a TB3010 2 BUSHINGS 2b 6T3207 2 GREASE ZERKS *3 33426 1 PIN (RO.
Cheetah Common Section 6-12 DAN FOSS V AL VE (06502095).
Cheetah Common Section 6-13 ITEM PART NO. QTY. DESCRIPTION 06502095 VL V ,5SP ,32PVG 1 06502074 1 END PLA TE 1S 06505013 1 END PLA TE SEAL KIT 2 * 5 BONNET 2 S 06505042 1 BONNET SEAL KIT 2 A 33459 1 M.
Cheetah Common Section 6-14 5SP HUSCO - POWER BEYOND (33500).
Cheetah Common Section 6-15 ITEM P ART NO. Q T Y DESCRIPTION 1 TB1017S 1 INLET END COVER 2 TB1702 1 END COVER, POWER BEYOND 3 TB1017P 1 V AL VE SECTION (SINGLE ACTING , SPRING DETENT) 4 TB1017N 1 V A .
Cheetah Common Section 6-16 5SP HUSCO - OPEN CENTER (34287).
Cheetah Common Section 6-17 ITEM P ART NO. QT Y DESCRIPTION 1 TB1017S 1 INLET END COVER 2 TB1701 1 END COVER, OPEN CENTER 3 TB1017P 1 V AL VE SECTION (SINGLE ACTION, SPRING DETENT) 4 TB1017N 1 V A L V.
Cheetah Common Section 6-18 4SP HUSCO LIFT V AL VE - FLAIL - OPEN CENTER (27671).
Cheetah Common Section 6-19 4SP HUSCO LIFT V AL VE - OPEN CENTER (27671) ITEM P ART NO. QT Y DESCRIPTION 1 TB1017S 1 INLET END COVER 2 TB1701 1 END COVER, OPEN CENTER 3 TB1017P 1 V AL VE SECTION (SING.
Cheetah Common Section 6-20 CHEET AH ROT AR Y MOTOR.
Cheetah Common Section 6-21 CHEET AH ROT AR Y MOTOR ITEM P ART NO. QTY . DESCRIPTION * 06504012 A V AI L M O TO R ASSEMBL Y - CHEET AH ROT ARY 1 22790 1 SHAFT END COVER 2 06504088 1 PORT END COVER 3 0.
Cheetah Common Section 6-22 ROT AR Y SPINDLE ASSEMBL Y.
Cheetah Common Section 6-23 ITEM PART NO. QTY. DESCRIPTION 1 6T1031 1 SPROCKET 2 6T1016 1 BEARING LOCK NUT - THICK 3 22596 1 JAM WASHER 4 6T1015 1 BEARING ADJUSTMENT NUT - THIN 5 6T1014 1 B EARING ADJ.
Cheetah Common Section 6-24 CHEET AH FLAIL HEAD ASSY ..
Cheetah Common Section 6-25 CHEET AH FLAIL HEAD ASSY . ITEM P/N Q T Y DESCRIPTION 1 33808 1 MOUNT ,DRIVE,CHEET AH,FLAIL 2 33806 1 SHIELD,DRIVE,CHEET AH,FLAIL 3 33805 1 MOUNT ,PLA TE,TREE,TBFS-40H 4 33.
Cheetah Common Section 6-26 CHEET AH FLAIL - CUTTER SHAFT ASSY ..
Cheetah Common Section 6-27 CHEET AH FLAIL - CUTTER SHAFT ASSY . ITEM P / N QTY DESCRIPTION 1 31723 1 CLAMP KIT ,TBF50 2 21679 4 CAPSCREW , 7/16" X 1" NC 3 31955 1 P L A TE, T OP , CLAMP , T.
Cheetah Common Section 6-28 CHEET AH FLAIL MOTOR.
Cheetah Common Section 6-29 CHEET AH FLAIL MOTOR ITEM P ART NO. QTY . DESCRIPTION * 06504019 A V AI L M O TO R ASSEMBL Y 350 - CHEET AH FLAIL 1 06504039 1 SHAFT END COVER 2 06504060 1 PORT END COVER 3.
Cheetah Common Section 6-30 CHEET AH CYLINDER BREAKDOWNS.
Cheetah Common Section 6-31 2” X 6” CYLINDER # 6T7022 ITEM P ART NO. QTY . DESCRIPTION 1 6T0162D 1 PISTON ROD 2 6T0165D 1 CYLINDER TUBE 3 6T0167D 1 CYLINDER BUTT 4 6T0170D 1 CYLINDER GLAND 5 6T017.
Cheetah Common Section 6-32 CHEET AH CYLINDER BREAKDOWNS.
Cheetah Common Section 6-33 CHEET AH CYLINDER BREAKDOWNS 3 1/2” X 14” CYLINDER # 33703 ITEM P ART NO. QTY . DESCRIPTION 1 33822 1 PISTON ROD 2 33823 1 CYLINDER TUBE 3 33824 1 CYLINDER BUTT 4 33825.
Cheetah Common Section 6-34 ITEM P ART NO. QTY . DESCRIPTION 06505044 A V AI L F I L TER ASSY SAE 10 MICRON 1 28583 4 C A P SCREW ,8MMX25MM(1.25 PITCH) 2 06505045 1 COVER 3 06505046 1 SE A L K I T 4 0.
Cheetah Common Section 6-35 BRAKE V AL VE ASSEMBL Y W/ METRI P AK ITEM PART NO. QTY. DESCRIPTION 1 34092 1 BRAKE VALVE, BLANK 2 34095 1 RELIEF VALVE, 3000 PSI 3 34094 2 LOGIC ELEMENT 4 06510095 1 METR.
Cheetah Common Section 6-36 DET AILS BOOM TRA VEL LOCK ITEM P ART NO. QTY . DESCRIPTION 1 31328 1 HYDRAULIC TRA VEL LOCK V AL VE 2 31329 1 ADAPTER - ST ANDARD BOOM 2A 3161 1 OPT . ADAPTER - EXTENDED BOOM 3 34532 1 SWITCH,TRA VEL LOCK 4 * REF . MAIN BOOM CYLINDER - REFER OT BOOM ASY 5 * REF .
Cheetah Common Section 6-37 SOLENOID BRAKE V AL VE HYDRAULIC SCHEMA TIC BRAKE V AL VE TROUBLESHOOTING F AILURE MODE: CHECK STEPS - MOWER WILL NOT ST AR T - system pressure is low (engine not lugging). 1 thru 6 - MOWER WILL NOT ST AR T - system pressure is high (engine lugging).
Cheetah Common Section 6-38 JOYSTICK SWITCHBOX SER VICE P ARTS ITEM P / N QTY . DESCRIPTION 1 06510196 1 SWBX,ASSY 2 3381 1 2 SWITCH,MASTER/DECK FLOA T 3 33813 1 SWITCH,SFTY SHIELD 4 34532 1 SWITCH,TR.
Cheetah Common Section 6-39 JOYSTICK SWITCHBOX SCHEMA TIC (06510196).
Cheetah Common Section 6-40 ITEM P / N Q TY . DESCRIPTION 1 06514012 1 SWBX,ALUM,BLK,06510100 2 35226 1 SWITCH,MOWER,COLEHERSEE 3 3381 1 1 SWITCH,MASTER/DECK FLOA T 4 34532 1 SWITCH,TRVL LCK 5 0651401.
Cheetah Common Section 6-41 P AGE INTENSIONALL Y LEFT BLANK.
Cheetah Common Section 6-42 OPTIONAL PUMP GUARD KIT ITEM PART NO. QTY. DESCRIPTION 1 32430 1 UNIVERSAL PUMP GUARD 2 21831 4 CAPSCREW - 3/4 X 1 3/4 3 21993 4 LOCKWASHER - 3/4 4 21825 4 HEX NUT - 3/4.
Cheetah Common Section 6-43 OPTIONAL PUMP AND GRILL GUARD KIT ITEM PART NO. QTY. DESCRIPTION 1 32430 1 UNIVERSAL PUMP GUARD 2 32737 1 UNIVERSAL GRILL GUARD 3 21833 4 CAPSCREW - 3/4 X 2 1/4 4 22021 2 F.
Cheetah Common Section 6-44 JOYSTICK TROUBLESHOOTING Boom operation not responding to joystick movement. Isolate hydraulic vs. electronic symptom. T urn off electronic master switch (preventing electronic actuator on valve from attempting to hold spool in neutral position).
Cheetah Common Section 6-45 Hydraulic inspection. Install 3 pressure gauges, on the valve inlet (use M port, or tee into hose supplying oil from the pump to the inlet), on the workport that is not operating, and on the LS port.
Cheetah Common Section 6-46 HYDRAULIC - TROUBLESHOOTING GUIDE.
Cheetah Common Section 6-47 ELECTRICAL - TROUBLESHOOTING GUIDE.
Cheetah Common Section 6-48 NOTES.
W ARRANTY SECTION Warranty Section 7-1.
..
W ARRANTY INFORMA TION T iger Corporation, 3301 N. Louise, Sioux Falls, South Dakota, warrants to the original Retail Customer , the new T iger equipment is free of defects in material and workmanship.
ONE LAST WORD This manual cannot possibly cover all of the potentially hazardous situations you will encounter . By being familiar with the safety rules, operating and maintenance instructions in this manual you can help prevent accidents. The objective of this manual is to help make you a better operator .
T O THE OWNER / OPERA TOR / DEALER T o keep your implement running efficiently and safely , read your manual thoroughly and follow these directions and the Safety Messages in this manual and on the machine. The table of contents clearly identifies each section where you can easily find the information you need.
Printed in USA © T iger Corporation.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Tiger Products Co., Ltd JD 5093E c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Tiger Products Co., Ltd JD 5093E - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Tiger Products Co., Ltd JD 5093E, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Tiger Products Co., Ltd JD 5093E va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Tiger Products Co., Ltd JD 5093E, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Tiger Products Co., Ltd JD 5093E.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Tiger Products Co., Ltd JD 5093E. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Tiger Products Co., Ltd JD 5093E ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
