Manuel d'utilisation / d'entretien du produit 96547iTP du fabricant Net Optics
Aller à la page of 52
User Guide iT ap GigaBit Dual Port Aggregator Models 96542iTP and 96547iTP Doc. PUB542iTPU Rev . 1, 3/06.
PLEASE READ THESE LEGAL NOTICES CAREFULL Y . By using a Net Optics iT ap GigaBit Dual Port Aggregator you agree to the terms and conditions of usage set forth by Net Optics, Inc. No licenses, express or implied, are granted with respect to any of the technology described in this manual.
iT ap GigaBit Dual Port Aggregator Contents Chapter 1 Introduction Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Memory . . . . . . . . . . . . . . . . . . . . . . . . . .
iT ap GigaBit Dual Port Aggregator Chapter 4 Using W eb Mana ger Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Accessing W eb Manager . . . . . . . . . . . . . . . . . . .
iT ap GigaBit Dual Port Aggregator 1 Chapter 1 Intr oduction Ov er view Thank you for purchasing the latest innovation in T ap technology – the iT ap GigaBit Dual Port Aggregator . Net Optics' GigaBit Dual Port Aggregator T aps provide ultra-ef fi cient access to critical GigaBit links using only one NIC on the monitoring device.
iT ap GigaBit Dual Port Aggregator 2 cally when the traf fi c volume falls below the receiving capacity of the NIC. These buffers allow the iT ap Port Aggregator to absorb traf fi c bursts without dropping packets. T raf fi c Monitoring The iT ap Port Aggregator monitors the utilization levels of both sides of the full- duplex link.
iT ap GigaBit Dual Port Aggregator 3 System Manager iT ap Port Aggregators can be used as a system managed via Simple Network Man- agement Protocol (SNMP) from a single interface. Net Optics' System Manager is an SNMP management tool that offers central management of all Net Optics iT ap devices in the network.
iT ap GigaBit Dual Port Aggregator 4 Memor y All traf fi c that passes through the iT ap is sent to the monitoring device NIC on a fi rst-in- fi rst-out basis, including traf fi c that is temporarily stored in memory .
iT ap GigaBit Dual Port Aggregator 5 The NIC receives 800 Mbps (80% utilization), so no memory is required for the monitoring device's NIC to process all full-duplex traf fi c.
iT ap GigaBit Dual Port Aggregator 6 Unpacking and Inspection Carefully unpack the iT ap GigaBit Dual Port Aggregator and check for damaged or missing parts.
iT ap GigaBit Dual Port Aggregator 7 Chapter 2 Installing the iT a p Ov er view This chapter describes how to install and connect the iT ap GigaBit Dual Port Aggregator .
iT ap GigaBit Dual Port Aggregator 8 Figure 4: 96547iTP Front Panel Features Figure 5: Rear panel features iT ap Port Aggregator LEDs Link Indicators: If a good link is established, the LED illuminates a steady green. Activity Indicators: If there is current activity on this link, the LED fl ashes.
iT ap GigaBit Dual Port Aggregator 9 Planning the Installation Before you begin the installation of your iT ap, you should determine the following information: IP address of the iT ap or , if you are deploying multiple iT aps, a range of IP addresses.
iT ap GigaBit Dual Port Aggregator 10 For security reasons, some parameters can only be set with the CLI. Use these commands to: Set CLI username and password Enable or disable the remote interfaces and display T urn character echo to the terminal emulation software on or off Y ou will fi nd a complete list of CLI commands in Appendix B.
iT ap GigaBit Dual Port Aggregator 11 T o change the username and password: 1. Change the username by typing the following command: set username <username> where <username> is your new username. 2. Change the password by typing the following command: set password <password> where <passwor d> is your new password.
iT ap GigaBit Dual Port Aggregator 12 T o set the current date and time: 1. T ype set time <mm/dd/yyyy-hh:mm:ss> where mm is the month, dd is the day of the month, yyyy is the year , hh is the hour, mm is minutes of the hour , and ss is seconds.
iT ap GigaBit Dual Port Aggregator 13 T o use the Help command: 1. T ype Help at the NetOptics prompt. The list of help topics is displayed. Figure 8: iT ap CLI Help Menu 5. T o view the syntax for changing the iT ap’ s con fi guration parameters, type help set and press Enter .
iT ap GigaBit Dual Port Aggregator 14 Connecting the Management Por t T o use the remote interfaces you must connect the Management Port to the network. T o connect the iT ap Management Port: 1. Connect a CA T5 cable to the Manangement Port as shown in Figure 9.
iT ap GigaBit Dual Port Aggregator 15 Figure 10: 96542iTP Network Connections Figure 11: 96547iTP Network Connections T o DTE network switch or router T o DCE network switch or router B 12 A www .netoptics.com ® RESET Network Monitor 1 2 B A Dual Port Aggregator GigaBit Copper TM LINK ACT LINK ACT LINK ACT LINK ACT ® www.
iT ap GigaBit Dual Port Aggregator 16 Connecting to the Monitoring De vices The iT ap comes with two monitor cables ready for iT ap installation. T o connect the iT ap to your monitoring device: 1. Connect Monitor Port 1 to the appropriate monitor using the cables supplied with your iT ap.
iT ap GigaBit Dual Port Aggregator 17 T o monitoring device 2 T o monitoring device 1 B 12 A www .netoptics.com ® RESET Network Monitor 1 2 B A Dual Port Aggregator GigaBit Copper TM LINK ACT LINK ACT LINK ACT LINK ACT Figure 13: 96547iTP Monitor Connections Connecting P ow er For power fault protection, the iT ap has redundant power supplies.
iT ap GigaBit Dual Port Aggregator 18 Figure 14: Connecting Power Checking the Installa tion After you have connected the iT ap to the network, monitoring device and power, verify that the iT ap is functioning correctly . Check that at least one power LED is illuminated.
iT ap GigaBit Dual Port Aggregator 19 Chapter 3 Using the F r ont Panel Interface Ov er view This chapter describes how to interpret and work with the front panel features of the iT ap GigaBit Dual Port Aggregator . The following topics are covered: Display LED indicators Reset Button The iT ap front panel provides information in two ways.
iT ap GigaBit Dual Port Aggregator 20 The percentage utilization data on the display is refreshed every second. Network peaks are given as a percent of utilization and re fl ect the highest peak recorded since the last reset. The day and time information re fl ects the highest peak event since reset.
iT ap GigaBit Copper Port Aggregator 21 Chapter 4 Using W eb Manager Ov er view This chapter describes how to monitor and control individual iT ap GigaBit Port Aggregators using W eb Manager .
iT ap GigaBit Copper Port Aggregator 22 Figure 15: Web Manager Page The following table explains the fi elds in W eb Manager . T o save any changes to the iT ap, you must click Submit Changes .
iT ap GigaBit Copper Port Aggregator 23 Viewing System Status Y ou can view status information of the iT ap and ports. System Status indicates if the iT ap is functioning correctly . If the System Status is DOWN, there is an inter- nal error . For more information, contact Net Optics' T echnical Support.
iT ap GigaBit Copper Port Aggregator 24 Viewing Statistics W eb Manager lists incoming traf fi c statistics for both Port A and Port B as shown in Figure 17. Figure 17: iT ap Statistics The following table explains the traf fi c statistics available from W eb Manager .
iT ap GigaBit Copper Port Aggregator 25 Con fi guring the iT a p W eb Manager has both read-only and read/write fi elds. Use the read/write fi elds in the iT ap Con fi guration section of the W eb Manager page to set con fi guration parameters (see Figure 18).
iT ap GigaBit Copper Port Aggregator 26 Field Name Function/V alue Description Port A Parameters Gigabit Auto-negotiation 100BT Full Duplex 100BT Half Duplex 10BT Full Duplex 10BT Half Duplex Disable The iT ap GigaBit Port Aggregator is a single-speed device.
iT ap GigaBit Dual Port Aggregator 27 Chapter 5 Using System Mana ger Ov er view This chapter describes how to install and use Net Optics' System Manager , which allows you to change settings, view status, and retrieve data remotely from mul- tiple Net Optics iT ap devices.
iT ap GigaBit Dual Port Aggregator 28 3. After reading the agreement, select I Agree and click Next to install System Manager . The W elcome dialog box appears as shown in Figure 20. Figure 20: Welcome Dialog Box 2. Click Next . The Select Installation Folder dialog box shown in appears.
iT ap GigaBit Dual Port Aggregator 29 4. T o limit access to System Manager to the current user of the PC, select Just Me . T o allow access to any user logged into the PC, select Everyone . 5. Click Next . The Con fi rm Installation dialog box shown in Figure 22 appears.
iT ap GigaBit Dual Port Aggregator 30 6. If you want to stop the installation, click Cancel . When the installation is com- plete, the Installation Complete dialog box appears as shown in Figure 24.
iT ap GigaBit Dual Port Aggregator 31 Exploring System Manager This section explains the features and functions of System Manager . W ith System Manager you can: Create iT ap groups Add and delete iT .
iT ap GigaBit Dual Port Aggregator 32 Tip! _____________________________________________________________________ T o use pop-up menu shortcuts, click your right mouse button in the System Frame. __________________________________________________________________________ Using the T oolbar Figure 26 shows the System Manager toolbar .
iT ap GigaBit Dual Port Aggregator 33 Figure 28: Group Bar 2. T ype the name of the new group and press Enter . Deleting a Group Y ou can delete a group however, all iT aps in that group will also be deleted. T o delete a Group: 1. Right click on the group bar of the group you want to delete.
iT ap GigaBit Dual Port Aggregator 34 Figure 30: New iT ap 2. Enter a name for the iT ap you are adding in the iT ap Name text box. Each iT ap Name in the system must be unique. 3. Enter the IP address of the iT ap in the IP Address text box. Make sure the IP address is unique on the network.
iT ap GigaBit Dual Port Aggregator 35 Figure 31: Net Optics System Manager with iT ap The indicator to the right of the iT ap picture blinks green when System Manager is communicating with the iT ap. If the indicator blinks red, check that the iT ap is connected to the network and verify the con fi guration information.
iT ap GigaBit Dual Port Aggregator 36 Deleting an iT ap Y ou can delete an iT ap from System Manager when you remove an iT ap from your network. If you have removed an iT ap from the network, System Manager con- tinues to poll the iT ap’ s IP address for data until you delete the iT ap from System Manager .
iT ap GigaBit Dual Port Aggregator 37 Con fi guring an iT a p Y ou can set con fi guration parameters of an iT ap in the system from the Con fi gure tab. T o con fi gure the iT ap: 1. Click on the icon of the iT ap you want to con fi gure and click the Con fi gure tab as shown in Figure 33.
iT ap GigaBit Dual Port Aggregator 38 Viewing iT a p Infor mation System Manager allows you to view the status of the iT ap, traf fi c statistics col- lected by the iT ap, and the current iT ap con fi guration information. T o view iT ap information: 1.
iT ap GigaBit Dual Port Aggregator 39 The Status tab is a read-only list of information from the iT ap. Use the scroll bar and arrows to view the entire list.
iT ap GigaBit Dual Port Aggregator 40 Modifying an iT ap Y ou can change the IP address and other basic iT ap con fi guration parameters from the Modify iT ap dialog box. T o modify the iT ap con fi guration: 1. Click on the image of the iT ap you want to change in the System Frame.
iT ap GigaBit Dual Port Aggregator 41 A ppendix A Speci fi ca tions and Models Speci fi cations Electrical Power Supply Input 100-240V AC, 0.5A, 47-63Hz Power Supply Output 12V , 1.
iT ap GigaBit Dual Port Aggregator 42 Optical Interface (96542iTP) Fiber T ype Corning Multimode 62.5/125 μ m, wavelength 850nm Split Ratio Network Port Insertion Loss Monitor Port Insertion Loss 70/30 ≤ 2.4 dB ≤ 6.3 dB 60/40 ≤ 3.1 dB ≤ 5.1 dB 50/50 ≤ 4.
iT ap GigaBit Dual Port Aggregator 43 Available Models Models 96542iTP iT ap GigaBit Fiber Dual Port Aggregator 96547iTP iT ap GigaBit Copper Dual Port Aggregator Wir eless Option Accessories RK-iTP2 .
iT ap GigaBit Dual Port Aggregator 44 A ppendix B Command Line Interface Command Sub-Command Syntax Description Help Set help set Displays the set command options. Reset help reset Displays the reset command options. Show help show Displays the show command options.
iT ap GigaBit Dual Port Aggregator 45 Command Sub-Command Syntax Description Reset Peak reset peak <port ID> Where <port ID> is A or B. Statistics reset statistics port <port ID> Where <port ID> is A or B. Storage reset storage Resets con fi guation to fac- tory defaults.
iT ap GigaBit Dual Port Aggregator 46 Notes:.
.
© 2006 by Net Optics, Inc. All Rights Reserved. www .netoptics.com.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Net Optics 96547iTP c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Net Optics 96547iTP - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Net Optics 96547iTP, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Net Optics 96547iTP va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Net Optics 96547iTP, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Net Optics 96547iTP.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Net Optics 96547iTP. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Net Optics 96547iTP ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
