Manuel d'utilisation / d'entretien du produit 99-7400 du fabricant Metra Electronics
Aller à la page of 8
99-7400 INSTALLA TION INSTRUCTIONS TOOLS REQUIRED Cutting tool Phillips screwdriver KIT COMPONENTS Radio Housing #1 Radio Housing #2 Faceplate #1 Faceplate #2 Bracket Set #9 Bracket Set #17 Bracket Se.
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (4) Phillips screws above the radio opening. Remove (1) Phillips screw below the left side of the radio opening. Remove (1) Phillips screw from each side of the dash trim bezel.
13 2 3 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (1) #10 Phillips screw from each side of the center console. Unsnap the coin tray and remove (2) #10 Phillips screws exposed. Lift the storage box carpet out and remove (2) #10 Phillips screws exposed.
3 12 Using the scored lines as a guide, cut and remove the dashed portions of Faceplate #1. Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip the dash trim bezel and remove. Remove (4) Phillips screws securing the factory head unit and disconnect the wiring.
11 4 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) screws from the top of the dash trim bezel and remove the bezel. Remove (4) fasteners from the factory head unit and disconnect the wiring. 1 NISSAN Axxess 1989-90 2 Using the scored lines as a guide, cut and remove the dashed portions of Faceplate #1.
5 10 Using the scored lines as a guide, cut and remove the dashed portions of Faceplate #2. Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the ashtray and (1) screw exposed in the top-right corner. Remove (2) Phillips screws above the climate controls.
9 6 Using the scored lines as a guide, cut and remove the dashed portions of Faceplate #2. Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the knobs from the climate controls. Using a small screwdriver, pry out on the climate control trim panel and remove.
7 8 3 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) Phillips screws from the bottom of the dash trim bezel. Remove (2) Phillips screws above the radio opening. Unclip the dash trim bezel and disconnect the defroster and rear wiper wiring.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Metra Electronics 99-7400 c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Metra Electronics 99-7400 - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Metra Electronics 99-7400, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Metra Electronics 99-7400 va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Metra Electronics 99-7400, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Metra Electronics 99-7400.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Metra Electronics 99-7400. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Metra Electronics 99-7400 ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.