Manuel d'utilisation / d'entretien du produit ScreenPlay SP8600HD3D du fabricant InFocus
Aller à la page of 53
.
Copyright This publication, including all photographs, illustratio ns and software, is protected under international copy- right laws, with all rights reserved. Neither this man ual, nor any of the material contained herein, may be reproduced without written consent of the autho r.
SP8600HD3D/IN8601 User’s Manual — ii — Important Safety Information Important: It is strongly recommended that you read this sect ion carefully be fore using the projector. These safety and usage instructions will ensure that you enj oy many years of safe use of the pr ojector.
Preface Projector Installation Notice ¾ Place the projector in a horizontal p osition The tilt angle of the projector should not exceed 15 degrees , nor should th e projector be in- stalled in any way other than the desktop and ce iling mount, otherwise lamp life could decrease dramatically, and may lead to other unpredictable damages .
SP8600HD3D/IN8601 User’s Manual Power Safety ¾ Only use the supplied power cord. ¾ Do not place anything on the powe r cord. Place the power cord where it will not be in the way of foot traffic. ¾ Remove the batteries from the remote control whe n storing or not in use for a prolonged period.
Preface – v – Table of Contents GETTING STARTED ........................................................................................................................................................... 1 P ACKING C HECKLIST .....................
SP8600HD3D/IN8601 User’s Manual — vi — T IMING M ODE T ABLE ........................................................................................................................................................ 39 P ROJECTOR D IMENSIONS ......
Preface – 1 – G ETTING S TARTED Packing Checklist Carefully unpack the projector and che ck that the following items are included: DLP P ROJ ECTO R R EMOTE CONTROL ( B ATTER IES NOT INCLUDED ) CD-.
SP8600HD3D/IN8601 User’s Manual Views of Projector Parts Front-right View 1 34 5 6 7 2 I TEM L ABEL D ESCRIP TION S EE PAGE : 1. Elevator button Push to release elevator foot 2. Elevator foot Adjusts level of projector 10 3. Lens Projection Lens 4. IR receiver Receives the remote control IR sign al 6 5.
Preface Top view—On-screen Displa y (OSD) buttons and LEDs Source Menu Enter Re-sync 11 10 12 1 2 4 5 6 3 7 8 9 I TEM L ABEL D ESCRIP TION S EE PAGE : Solid Green Power On / Standby 1. Power LED Off Power Off (AC Off) Solid Red The lamp is powered on.
SP8600HD3D/IN8601 User’s Manual Rear view 12 3 4 56 7 8 9 10 11 12 13 14 I TEM L AB E L D ESCRIPTION S EE PAGE : 1. AC IN Connect the POWER CABLE. 9 2. COMPONENT Connect the COMPONENT CABLE from a display. 3. COMPOSITE Connect the COMPOSITE CABLE from a video device.
Preface Bottom view 51.5 65.0 71.0 90.5 109.0 76.0 12 2 34 I TEM L ABEL D ESCRIPTION S EE PAGE : 1. Leveling foot Rotate leveling foot to adjust angle position. 10 2. Ceiling support holes Only use with an InFocus ceiling mount system (p/n PRJ-M NT-UNIV).
SP8600HD3D/IN8601 User’s Manual Remote Control Par ts 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 5 16 17 18 19 20 21 22 23 24 2 5 26 27 28 29 30 31 Important: 1. Avoid using the projector with bright fluoresc ent lighting turned on. Certain high-frequency fluo- rescent lights can disrupt remote control operation.
Preface – 7 – I TEM L ABEL D ESCRIP TION S EE PAGE : 1. Power ON Turn the projector on. 9 2. LED indicator Only lights when t he remote keys are pressed. 3. Display Mode Choose a suitable preset mode for usage environment. 4. Contrast Display the Contrast setting bar and use the right and left keys to adjust.
SP8600HD3D/IN8601 User’s Manual — 8 — S ETUP AND O PERATION Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the di- rection of the arrow. 2. Insert the batteries (not included) as shown in the illustration.
Preface Starting and Shutting down t he Projec tor 1. Connect the power cord to the pro- jector. Connect the other end to a wall outlet. The POWER LED will be on. 2. Turn on the connected devices. 3. Ensure the POWER LED dis- plays a solid green. Then press the Power ON button on the projector keypad or remote ( ).
SP8600HD3D/IN8601 User’s Manual Adjusting the Projector Level Take note of the following when setting up the projector: • The projector t able or stand should be level and sturdy . • Position the projector so that it is perpendicular t o the screen.
Preface Adjusting the Zoom ring, Focus and Keystone 1. Use the Zoom control (on the projector only) to resize the projected image and screen size B . 2.
SP8600HD3D/IN8601 User’s Manual Adjusting the Volume 1. Press the Volume but- tons (on the projector or the remote control). The volume control appears on the display. 2. Use the Vol +/- buttons (on the projector or the remote control). 3. Press the MUTE button to turn off the audio (This feature is avail- able only on the remote).
Preface – 13 – O N -S CREEN D ISPLAY (OSD) M ENU S ETTINGS OSD Menu Controls The projector has an OSD that lets you ma ke image adjustments and c hange various settings. Navigating the OSD You can use the remote control cu rsor buttons or the projector ke ypad to navigate and make changes to the OSD.
SP8600HD3D/IN8601 User’s Manual Setting the OSD Language Set the OSD language to your pr eference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to SETUP>>Basic . 2. Press the cursor ▲▼ button until Language is highlighted.
Preface OSD Menu Overview Use the following illustration to quickly find a se tting or determine the range for a setting. – 15 –.
SP8600HD3D/IN8601 User’s Manual PICTURE>>Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE>>Basic menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Basic menu.
Preface PICTURE>>Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE>>Advanced menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Advanced menu. Press ◄► to change values for settings.
SP8600HD3D/IN8601 User’s Manual HSG Adjustment Press the ENTER/SELECT button to enter the HSG Adjustment sub menu. I TEM D ESCRIP TION Primary Color Press the ◄► buttons to set the Primary Color. Notes: There are si x colors ( R / G/ B/ C/ M/ Y) to be cu stomized.
Preface DISPLAY Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the DISPLAY menu. Press the cursor ▲▼ button to move up and down in the DISPLAY menu. Press ◄► to change values for settings. I TEM D ESCRIPTION Aspect Ratio Press the cursor ◄► button to set the Aspect Ratio.
SP8600HD3D/IN8601 User’s Manual PC Detail Adjustment Press the ENTER/SELECT button to enter the PC Detail Adjustment sub menu. Note: Customizing the settings in PC Detail Adjustment menu is only available when PC input source (analog RGB) is selected.
Preface 3D Settings I TEM D ESCRIPTION 3D mode Press the cursor ◄► button to to enable or disable 3 D Mode. 2D to 3D mode Press the cursor ◄► button to enable or disable 2D to 3D mode. 3D Type Press the cursor ◄► button to select 96Hz or 120Hz when a 10 80p 24Hz "Frame Packing" 3D fo rmat is used.
SP8600HD3D/IN8601 User’s Manual SETUP>>Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SETUP>>Basic menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Basic menu.
Preface Menu Settings Press the ENTER/SELECT button to enter the Menu Settings sub menu. I TEM D ESCRIP TION Menu Position Press the ◄► buttons to select from five OSD locations: Top-Left/ Top-Right/ Center / Bottom-Left/ Bottom-Right. Menu Display Time Press the ◄► buttons to set the Menu Display timer before the OSD times out.
SP8600HD3D/IN8601 User’s Manual SETUP>>Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SETUP>>Advanced menu. Press the cursor ▲▼ button to move up and down in the SETUP>>Advanced menu.
Preface Audio Press the ENTER/SELECT button to enter the Audio sub menu. I TEM D ESCRIP TION Volume Press the ◄► buttons to adjust the audio Volume. Treble Press the ◄► buttons to adjust the audio Treble. Bass Press the ◄► buttons to adjust the audio Bass.
SP8600HD3D/IN8601 User’s Manual Closed Caption Press the ENTER/SELECT button to enter the Closed Caption sub menu. I TEM D ESCRIPTION Closed Caption En- able Press the ◄► buttons to turn on or off Closed Caption. Caption Version Press the ◄► buttons to select the Caption Version.
Preface STATUS Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the STATUS Menu . I TEM D ESCRIP TION Display Mode Displays the current displa y mode. Aspect Displays the current aspect ratio setting. Source Displays the activated input source.
SP8600HD3D/IN8601 User’s Manual — 28 — M AINTENANCE AND S ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. Be sure to use the InFocus lamp module de- signed for this projector. You can order new lamps from www.
Preface 2. Remove the single screw on the lamp compartment cover, using a small Philips screwdriver. 3. Remove the lamp com- partment cover. 4. Remove the three screws from the lamp module , using a small Philips screwdriver . 5. Lift the module handle up.
SP8600HD3D/IN8601 User’s Manual 6. Pull firmly on the module handle to remove the lamp module. 7. Reverse steps 1 to 6 to in- stall the new lamp module. While installing, align the lamp module with the connector and ensure it is level to avoid damage.
Preface – 31 – Cleaning the Projector Cleaning the projector to remove dust and gr ime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at least 60 minutes before cleaning. Failure to do so could result in a severe burn.
SP8600HD3D/IN8601 User’s Manual — 32 — T ROUBLESHOOTING Common Problems and Solutions These guidelines provide tips to deal with problem s you may encounter while using the projector. If the problem remains unsolved, cont act your dealer for assistance.
Preface – 33 – LED Error Messages E RROR C ODE M ESSAGE S P OWER LED L AMP / R EADY LED T EMP LED Powered on Solid Green Solid Red OF F Powering up Solid Green Flashing Red OFF Cooling down Solid .
SP8600HD3D/IN8601 User’s Manual — 34 — 1. Set the Frequenc y and Phase setting s on the Display >> PC Detail Adjustment menu of the OSD to the default settings. 2. To ensure the problem is not caused by a connected PC’ s video card, conn ect to another computer.
Preface – 35 – Audio Problems Problem: There is no sound 1. Adjus t the volume on the remote control. 2. Adjust the volume of the audio source. 3. Check the audio cable connection. 4. Test the source audio output with other speakers. 5. Have the projector serviced.
SP8600HD3D/IN8601 User’s Manual — 36 — HDMI Q & A Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI cable? Recently, HDMI Licensing, LLC announ ced that cables would be tested as Standard or High- Speed cables.
Preface – 37 – S PECIFICATIONS Specifications Model SP8600HD3D/IN8601 Display ty pe TI DLP DMD 0.65” Native Resolution 1920 x 1080 Projection distance 1 meters ~ 10 meters ( 3.28 ft ~ 32.8 ft ) Projection screen size 23.5" ~ 300" ( 59.
SP8600HD3D/IN8601 User’s Manual Projection Distance vs. Projection Si ze Projection Distance and Size Table 16:9 SCREEN PROJECTION DISTANCE DIAGONAL WIDTH HEIGHT INCH MM MM ( INCH ) MM ( INCH ) MIN .
Preface – 39 – Timing Mode Table The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector. S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE C OMPONENT RGB ( ANALOG ) HDMI ( DIGITAL ) NTSC — 15.
SP8600HD3D/IN8601 User’s Manual — 40 — S IGNAL R ESOLUTION H-S YNC (KH Z ) V-S YNC (H Z ) C OMPOSITE C OMPONENT RGB ( ANALOG ) HDMI ( DIGITAL ) 480p 31.5 60.0 — O O O 720p 37.5 50.0 — O O O 720p 45.0 60.0 — O O O 1080i 33.8 60.0 — O O O 1080i 28.
Preface – 41 – 3D support timings: Frame sequential R ESOLUTION V-S YNC (H Z ) C OMPOSITE C OMPONENT RGB ( ANALOG ) HDMI ( DIGITAL ) 720p 100Hz — — — O 720p 120Hz — — — O Frame packing.
SP8600HD3D/IN8601 User’s Manual Projector Dimensions — 42 —.
Preface – 43 – R EGULATORY C OMPLIANCE FCC Warning This equipment has been tested and found to comply wi th the limits for a Class B digital device pur- suant to Part 15 of the FCC Rules. These lim its are designed to provide reasonable protection against harmful interference when the equipm ent is operated in a commercial environment.
SP8600HD3D/IN8601 User’s Manual — 44 — RS-232C Protocol RS232 Setting Baud rate: 9600 Parity check: None Data bit: 8 Stop bit: 1 Flow Control None Minimum delay for next command: 1ms Control Command Structure The command is structured by the H eader code, command code, data code and end code.
Preface – 45 – Remote Command The remote commands simulate the code send from IR remote handset. Button’s name ASCII HEX UP arrow ~ r U C R 7Eh 72h 55h 0Dh DOWN arrow ~ r D C R 7Eh 72h 44h 0Dh L.
SP8600HD3D/IN8601 User’s Manual — 46 — Query Command ITEM ASCII HEX Software Version ~ q V C R 7Eh 71h 56h 0Dh Power State ~ q P C R 7Eh 71h 50h 0Dh Input Select ~ q S C R 7Eh 71h 53h 0Dh Lamp H.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté InFocus ScreenPlay SP8600HD3D c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du InFocus ScreenPlay SP8600HD3D - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation InFocus ScreenPlay SP8600HD3D, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le InFocus ScreenPlay SP8600HD3D va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le InFocus ScreenPlay SP8600HD3D, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du InFocus ScreenPlay SP8600HD3D.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le InFocus ScreenPlay SP8600HD3D. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei InFocus ScreenPlay SP8600HD3D ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
