Manuel d'utilisation / d'entretien du produit 130HS du fabricant Graco
Aller à la page of 34
Repair - Parts List LineLazer ™ 130 HS Airless Paint Striper For application of line striping materials. For professional use only. Not for use in explosive atmospheres. 3300 psi (22.8 MPa, 228 bar) Maximum Working Pressure . 257780 ✔✔ 287025 ✔✔ ✔ Important Safety Instructions Read all warnings and instructions in this manual.
2 313776G Contents W a r n i n g s ................................. 3 T i pS e l e c t i o n .............................. 5 General Repair Information .................. 6 Maintenance ............................... 7 Troubleshooting ..............
Warnings 313776G 3 Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings.
Warnings 4 313776G EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury. • Do not operate the unit when fatigued or under the influence of drugs or alcohol. • Do not exceed the maximum working pressure or temperature rating of the lowest rated system component.
Tip Selection 313776G 5 Tip Selection * Use 100 mesh filter to reduce tip clogs. LL5213* 2( 5 ) ✔ LL5215* 2( 5 ) ✔ LL5217 4 (10) ✔ LL5219 4 (10) ✔ LL5315 4 (10) ✔ LL5317 4 (10) ✔ LL5319 4 .
General Repair Information 6 313776G General Repair Information 1. Keep all screws, nuts, washers, gaskets, and electrical fittings removed during repair proce- dures. These parts are not normally provided with replacement assemblies. 2. Test repair after problem is corrected.
Maintenance 313776G 7 Maintenance Pressure Relief Procedure 1. Engage trigger lock. 2. Turn engine ON/OFF switch to OFF. 3. Move pump valve to OFF (clockwise) and turn pres- sure control knob fully counterclockwise. 4. Disengage the trigger lock. Hold a metal part of the gun firmly to a grounded metal pail, and trigger the gun to relieve pressure.
Troubleshooting 8 313776G Troubleshooting Problem Cause Solution Gas engine pulls hard (won't start). Hydraulic pressure is too high. Turn hydraulic pressure knob counterclockwise to lowest setting. Engine won't start. Engine switch is OFF. Turn engine switch ON.
Troubleshooting 313776G 9 Displacement pump operates, but output is low on upstroke Piston ball is not seating. Service piston ball. Manual 311845. Piston packings are worn or damaged. Replace packings. Manual 311845. Displacement pump operates but output is low on downstroke and/or on both strokes.
Troubleshooting 10 313776G Excessive leakage around hydraulic motor piston rod wiper. Piston rod seal worn or damaged. Replace these parts. Fluid delivery is low. Pressure setting too low. Increase pressure. Manual 313775. Displacement pump outlet filter (if used) is dirty or clogged.
Hydraulic Pump 313776G 11 Hydraulic Pump Removal 1. Allow hydraulic system to cool before beginning ser- vice. 2. Relieve pressure, page 7. 3. Place drip pan or rags under sprayer to catch hydraulic oil that leaks out during repair. 4. Remove drain plug (195) and oil filter (199) and allow hydraulic oil to drain.
Hydraulic Pump 12 313776G F IG .2 TI6551a 224 24 162 169 86 143 241 195 85 A 215 237 35 178 252 180 218 184 199 32 251 196 182 101.
Fan Belt 313776G 13 Fan Belt Removal 1. Relieve pressure, page 7. 2. F IG . 3. Loosen belt guard knob (241). 3. Rotate belt guard (24) up. 4. Lift engine (185) up to remove tension on belt (143). 5. Remove belt from fan pulley (86) and fan pulley (87a).
Engine 14 313776G Engine NOTE: All service to the engine must be performed by an authorized HONDA dealer, Removal 1. Relieve pressure, page 7. 2. Do Fan Belt , Removal ; page 13. 3. Loosen hand nut (241). Swing bracket (30) out. 4. F IG . 4. Disconnect red and black leads from engine.
Hydraulic Motor Yoke 313776G 15 Hydraulic Motor Yoke Removal 1. Relieve pressure, page 7. 2. Place drip pan or rags under sprayer to catch hydraulic oil that leaks out during repair. 3. F IG . 5. Slide retainer clip (194) down to remove. Remove pump pin (249).
Hydraulic Motor Yoke 16 313776G F IG .5 $ WHVWKROH ti13918a.
Oil/Filter Change 313776G 17 Oil/Filter Change Removal 1. F IG . 6 Place drip pan or rags under sprayer to catch hydraulic oil that drains out. 2. Remove drain plug (195). Allow hydraulic oil to drain. 3. Unscrew filter (199) slowly - oil runs into groove and drains out rear.
Displacement Pump 18 313776G Displacement Pump See manual 311845 for pump repair instructions. Removal 1. Flush pump. 2. Relieve pressure, page 7. 3. F IG . 7. Remove suction tube (34) and hose (26). 4. F IG . 8. Push retaining spring (194) up. Push out pin (249).
Parts 313776G 19 Parts LineLazer IV 130 HS Parts Page 30 Parts Page 26 Parts Page 28 Parts Page 34 Parts Page 34 ti13917a Parts Pa g e3 6 Parts Page 28.
Parts 20 313776G 36 290 144 57 141 27 108 5 129 156 93 73 74 58 117 70 134 261 121 258 16 121 256 117 99 122 117 51 156 94 84 142 127 120 13 60 108 33 154 112 261 28 ti13910a 2 1.
Parts 313776G 21 LineLazer IV 130 HS Ref Part Description Qty 5 237686 CLAMP, grounding assy 1 13 245225 HOSE, 3/8 in. x 50 ft 1 16 287623 FRAME, linestriper (painted) 1 27 287417 HANDLE 1 28 287622 S.
Parts 22 313776G LineLazer IV 130 HS WLD 49 136 360 117 161 1 105 14 4 8 47 44 104 8a 46 83 121 8e 8f 8b 8c 8f 8f 8f 8d 1 Detail 8 Ref 161 163 96 161 71 72 144 119 162 89 71 17 119 27 160 .
Parts 313776G 23 LineLazer IV 130 HS Ref Part Description Qty 1 224052 BRACKET, support gun 1 4 248157 GUN, flex, basic, includes guard & tip 1 8 287570 KIT, holder, gun 1 8a 287569 HOLDER, gun 1 .
Parts 24 313776G Parts - LineLazer IV 130 HS 72(1*,1( (1*,1(2)) 6:,7&+ *5281' 81 185a 151 97 15f ti13916a 259 124 62 13 29 27 267 15f 15s 103 31 302 310 103 97 62 303 308 11 37.
Parts 313776G 25 LineLazer IV 130 HS Ref Part Description Qty 2* 245103 VALVE, drain 1 2a 193709 SEAT, valve 1 2b 193710 SEAT, valve 1 2c 116424 NUT, cap 1 2d 114708 SPRING 1 11* 244067 FILTER, fluid 1 13 245225 HOSE, 3/8 in. x 50 ft 1 15f 114954 SWITCH, rocker 1 15s ▲ 15Y608 LABEL, control 1 26 245226 HOSE, coupled, 3/8 in.
Parts 26 313776G Parts - LineLazer IV 130 HS 250 173 217 231 235 176 138 159 69 217 243 285 35 149 173 283 107 48 183 235 220 186 187 213 34 174 32 137 35 218 222 21 60 26 285 213 245 179 244 108 230 .
Parts 313776G 27 LineLazer IV 130 HS Ref Part Description Qty 21 24B748 PUMP, displacement 1 Manual 311845 26 245797 HOSE, coupled, 3/8 in. 1 32 287175 HOSE, hydraulic, supply 1 34 287206 HOSE, suction/drain 1 35 287176 HOSE, hydraulic, return 1 48 117328 FITTING, nipple, straight 1 60 196178 ADAPTER, nipple 3/8 in.
Parts 28 313776G LineLazer IV 130 HS TI6493b 34g 34n 34a 34d 34h 34b 34k 34d 34j 34c 34f 34e Detail 34 169 86 24 193 241 225 214 224 23 143 184 178 82 228 198 215 174 75 252 180 189 197 237 114 114 59.
Parts 313776G 29 LineLazer IV 130 HS Ref Part Description Qty 23 288261 RAIL, belt 1 24 248973 GUARD, belt, includes: 162, 193, 214, 224, and 228 1 30 15E476 BRACKET, retainer, motor 1 32 287175 HOSE,.
Parts 30 313776G LineLazer IV 130 HS TI6492b 53 131 106 108 121 7 147 130 127 F 140 153 46 117 56 146 141 142 127 130 133 10 133 132 116 55 52 139 110 46 145 135 6 65 209 128 54 113 Detail A 139 1 Det.
Parts 313776G 31 LineLazer IV 130 HS Ref Part Description Qty 6 240942 SHAFT, fork 1 7 240991 BRACKET, caster, front 1 10* 15G952 BRACKET, hub 1 16 287623 FRAME, linestriper, painted 1 46 181818 KNOB,.
Technical Data 32 313776G Technical Data Accessories Must be purchased separately. GRACO-APPROVED HYDRAULIC OIL Honda GX160 Engine Power Rating @ 3600 rpm ANSI ..................................... 4 . 0H o r sepower Maximum working pressure .........
Notes 313776G 33 Notes.
All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. For patent information, see www.graco.com/patents 2ULJLQDOLQVWUXFWLRQV This manual contains English.
Un point important après l'achat de l'appareil (ou même avant l'achat) est de lire le manuel d'utilisation. Nous devons le faire pour quelques raisons simples:
Si vous n'avez pas encore acheté Graco 130HS c'est un bon moment pour vous familiariser avec les données de base sur le produit. Consulter d'abord les pages initiales du manuel d'utilisation, que vous trouverez ci-dessus. Vous devriez y trouver les données techniques les plus importants du Graco 130HS - de cette manière, vous pouvez vérifier si l'équipement répond à vos besoins. Explorant les pages suivantes du manuel d'utilisation Graco 130HS, vous apprendrez toutes les caractéristiques du produit et des informations sur son fonctionnement. Les informations sur le Graco 130HS va certainement vous aider à prendre une décision concernant l'achat.
Dans une situation où vous avez déjà le Graco 130HS, mais vous avez pas encore lu le manuel d'utilisation, vous devez le faire pour les raisons décrites ci-dessus,. Vous saurez alors si vous avez correctement utilisé les fonctions disponibles, et si vous avez commis des erreurs qui peuvent réduire la durée de vie du Graco 130HS.
Cependant, l'un des rôles les plus importants pour l'utilisateur joués par les manuels d'utilisateur est d'aider à résoudre les problèmes concernant le Graco 130HS. Presque toujours, vous y trouverez Troubleshooting, soit les pannes et les défaillances les plus fréquentes de l'apparei Graco 130HS ainsi que les instructions sur la façon de les résoudre. Même si vous ne parvenez pas à résoudre le problème, le manuel d‘utilisation va vous montrer le chemin d'une nouvelle procédure – le contact avec le centre de service à la clientèle ou le service le plus proche.
