FR
Ryobi logo
Notice d'utilisation officielle

Ryobi One+ Circular Saw (P500)

68 pages·3.4 MB·Scie sans fil·PDF·ENDEITNLJA
Ryobi One+ Circular Saw (P500)
Table des matières 64 sections OPERATOR’S MANUAL · 5-1/2 in., 18 VOLT LASER CIRCULAR SAW · P500 · BATTERIES AND CHARGERS SOLD SEPARATELY · … AfficherMasquer
Page 1 of the Ryobi One+ Circular Saw (P500) user manual — SAVE THIS MANUAL FOR FUTURE REFERENCE
Page 1 · cliquer pour agrandir
Page 1

OPERATOR’S MANUAL

5-1/2 in., 18 VOLT LASER CIRCULAR SAW

P500

Ryobi One+ Circular Saw (P500) — OPERATOR’S MANUAL diagram (page 1)
Fig. 1

BATTERIES AND CHARGERS SOLD SEPARATELY

Your laser circular saw has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

Thank you for your purchase.

SAVE THIS MANUAL FOR FUTURE REFERENCE

Page 3 of the Ryobi One+ Circular Saw (P500) user manual — PERSONAL SAFETY Stay alert, watch what you are doing and use
Page 3 · cliquer pour agrandir
Page 3

GENERAL SAFETY RULES

Do not overreach. Keep proper footing and balance

at all times. Proper footing and balance enable better control of the tool in unexpected situations. Use safety equipment. Always wear eye protection.

Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. Do not wear loose clothing or jewelry. Contain long

SAVE THESE INSTRUCTIONS WORK AREA Keep your work area clean and well lit. Cluttered

hair. Loose clothes, jewelry, or long hair can be drawn into air vents. Do not use on a ladder or unstable support. Stable

benches and dark areas invite accidents. Do not operate power tools in explosive atmo

footing on a solid surface enables better control of the tool in unexpected situations. TOOL USE AND CARE Use clamps or other practical way to secure and sup

spheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. Keep bystanders, children, and visitors away while

port the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. Do not force tool. Use the correct tool for your

operating a power tool. Distractions can cause you to lose control. ELECTRICAL SAFETY A battery operated tool with integral batteries or a

application. The correct tool will do the job better and safer at the rate for which it is designed. Do not use tool if switch does not turn it on or off.

separate battery pack must be recharged only with the specified charger for the battery. A charger that may be suitable for one type of battery may create a risk of fire when used with another battery. Use battery operated tool only with specifically

A tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect battery pack from tool or place the switch

in the locked or off position before making any adjust ments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. Store idle tools out of reach of children and other

designated battery pack. Use of any other batteries may create a risk of fire. Use battery only with charger listed.

MODELBATTERY PACKCHARGER (P113) P500(P104 Li-ion) 130429001, 130429002 130155001 (P100 Ni-Cd) 130255004, 130224028140501001 140501005 BATTERY PACKCHARGER (P110) (P100 Ni-Cd) 130255004, 1302240281423701, 140237021, 140237023

untrained persons. Tools are dangerous in the hands of untrained users. When battery pack is not in use, keep it away from

other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns, or a fire. Maintain tools with care. Keep cutting tools sharp

and clean. Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control. Check for misalignment or binding of moving parts,

PERSONAL SAFETY Stay alert, watch what you are doing and use

breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. Use only accessories that are recommended by the

common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. Dress properly. Do not wear loose clothing or jewelry.

manufacturer for your model. Accessories that may be suitable for one tool may create a risk of injury when used on another tool. Keep the tool and its handle dry, clean and free from

Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. Avoid accidental starting. Be sure switch is in the

oil and grease. Always use a clean cloth when clean ing. Never use brake fluids, gasoline, petroleum-based products, or any strong solvents to clean your tool. Fol lowing this rule will reduce the risk of loss of control and deterioration of the enclosure plastic.

locked or off position before inserting battery pack. Carrying tools with your finger on the switch or inserting the battery pack into a tool with the switch on invites accidents. Remove adjusting keys or wrenches before turning

the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.

Page 4 of the Ryobi One+ Circular Saw (P500) user manual — SPECIFIC SAFETY RULES
Page 4 · cliquer pour agrandir
Page 4

GENERAL SAFETY RULES

SERVICE Tool service must be performed only by qualified

When servicing a tool, use only identical replacement

parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to fol low Maintenance Instructions may create a risk of shock or injury.

repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury.

SPECIFIC SAFETY RULES

When ripping, always use a rip fence or straight edge

blade. Keep your second hand on the auxiliary handle or motor housing. If both hands are holding the saw, they cannot be cut by the blade. Keep your body positioned to either side of the saw

guide. This improves the accuracy of the cut and reduces the chance for blade binding. Always use blades with correct size and shape

(diamond vs. round) arbor holes. Blades that do not match the mounting hardware of the saw will run eccentrically, causing loss of control. Never use damaged or incorrect blade washers

blade, but not in line with the saw blade. KICKBACK could cause the saw to jump backwards. (See “Causes And Operator Prevention Of Kickback” later.) Do not reach underneath the work. The guard cannot

or bolts. The blade washers and bolts were specially designed for the saw for optimum performance and safety of operation. CAUSES AND OPERATOR PREVENTION OF KICKBACK:

protect you from the blade below the work. Check lower guard for proper closing before each use.

Do not operate saw if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position. If saw is accidentally dropped, lower guard may be bent. Raise the lower guard with the retracting handle. Make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut. Check the operation and condition of the lower guard

Kickback is a sudden reaction to a pinched, bound, or mis aligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator.

When the blade is pinched or bound tightly by the kerf clos ing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator.

spring. If the guard and the spring are not operating properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris. Lower guard should be retracted manually only for

If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the kerf and jump back toward the operator.

special cuts, such as "Pocket Cuts" and "Compound Cuts." Raise lower guard by retracting handle. As soon as blade enters the material, lower guard must be released. For all other sawing, the lower guard should operate automatically. Always observe that the lower guard is covering the

Kickback is a result of tool misuse and/or incorrect operat ing procedures or conditions and can be avoided by taking proper precautions as given below:

Maintain a firm grip on the saw and position your body

and arm in a way that allows you to resist KICKBACK forces. KICKBACK forces can be controlled by the opera tor, if proper precautions are taken.

blade before placing saw down on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released. NEVER hold piece being cut in your hands or across

When blade is binding, or when interrupting a cut

for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or KICKBACK may occur. Investigate and take corrective actions to eliminate the cause of blade binding.

your leg. It is important to support the work properly to minimize body exposure, blade binding, or loss of control. Hold tool by insulated gripping surfaces when

performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator.

When restarting a saw in the workpiece, center the

saw blade in the kerf and check that teeth are not engaged into the material. If saw blade is binding, it may walk up or KICKBACK from the workpiece as the saw is restarted.

Page 5 of the Ryobi One+ Circular Saw (P500) user manual — SPECIFIC SAFETY RULES
Page 5 · cliquer pour agrandir
Page 5

SPECIFIC SAFETY RULES

Support large panels to minimize the risk of blade

Battery tools do not have to be plugged into an elec

pinching and KICKBACK. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel. Do not use dull or damaged blade. Unsharpened or

trical outlet; therefore, they are always in operating condition. Be aware of possible hazards when not using your battery tool or when changing accessories. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

improperly set blades produce narrow kerf which causes excessive friction, blade binding and KICKBACK. Blade depth and bevel adjusting locking levers

Do not place battery tools or their batteries near fire

or heat. This will reduce the risk of explosion and pos sibly injury.

must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and KICKBACK. Use extra caution when making a “Pocket Cut” into

Batteries can explode in the presence of a source

of ignition, such as a pilot light. To reduce the risk of serious personal injury, never use any cordless product in the presence of open flame. An exploded battery can propel debris and chemicals. If exposed, flush with water immediately.

existing walls or other blind areas. The protruding blade may cut objects that can cause KICKBACK. ADDITIONAL SAFETY RULES Know your power tool. Read operator's manual care

Do not charge battery tool in a damp or wet location.

Following this rule will reduce the risk of electric shock.

fully. Learn its applications and limitations, as well as the specific potential hazards related to this tool. Following this rule will reduce the risk of electric shock, fire, or serious injury.

For best results, your battery tool should be charged

in a location where the temperature is more than 50°F but less than 100°F. Do not store outside or in vehicles.

Always wear safety glasses with side shields. Everyday

glasses have only impact resistant lenses. They are NOT safety glasses. Following this rule will reduce the risk of eye injury.

Under extreme usage or temperature conditions,

battery leakage may occur. If liquid comes in contact with your skin, wash immediately with soap and water, then neutralize with lemon juice or vinegar. If liquid gets into your eyes, flush them with clean water for at least 10 minutes, then seek immediate medical at tention. Following this rule will reduce the risk of serious personal injury.

Protect your lungs. Wear a face or dust mask if the

operation is dusty. Following this rule will reduce the risk of serious personal injury.

Protect your hearing. Wear hearing protection during

extended periods of operation. Following this rule will reduce the risk of serious personal injury.

If the power supply cord is damaged, it must be replaced

only by the manufacturer or by an authorized service center to avoid risk. Laser Guide Warnings The laser guide radiation used in this circular saw is Class II with maximum

Inspect tool cords periodically and, if damaged, have

repaired at your nearest Authorized Service Center. Constantly stay aware of cord location. Following this rule will reduce the risk of electric shock or fire.

Check damaged parts. Before further use of the

tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other condi tions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center. Following this rule will reduce the risk of shock, fire, or serious injury.

with the manufacturer’s instructions. Never aim the beam at a person or object other than the

workpiece. Always ensure the laser beam is aimed at a sturdy

workpiece without reflective surfaces. Shiny reflective sheet metal or similar shiny materials are not suitable for laser use. All repairs should be made by an authorized service

Inspect for and remove all nails from lumber before

using this tool. Following this rule will reduce the risk of serious personal injury.

representative or the laser manufacturer. Save these instructions. Refer to them frequently and

Drugs, alcohol, medication. Do not operate tool while

use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also.

under the influence of drugs, alcohol, or any medica tion. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Page 6 of the Ryobi One+ Circular Saw (P500) user manual — SYMBOLS
Page 6 · cliquer pour agrandir
Page 6

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper inter pretation of these symbols will allow you to operate the product better and safer. SYMBOL NAME DESIGNATION/EXPLANATION VVoltsVoltage AAmperesCurrent HzHertzFrequency (cycles per second) WWattPower minMinutesTime Alternating CurrentType of current Direct CurrentType or a characteristic of current n oNo Load SpeedRotational speed, at no load Class II ConstructionDouble-insulated construction .../minPer MinuteRevolutions, strokes, surface speed, orbits etc., per minute Wet Conditions AlertDo not expose to rain or use in damp locations. Read The Operator’s ManualTo reduce the risk of injury, user must read and understand operator’s manual before using this product. Eye ProtectionAlways wear safety goggles or safety glasses with side shields and, as necessary, a full face shield when operating this product. Safety AlertPrecautions that involve your safety. No Hands SymbolFailure to keep your hands away from the blade will result in seri ous personal injury. No Hands SymbolFailure to keep your hands away from the blade will result in seri ous personal injury. No Hands SymbolFailure to keep your hands away from the blade will result in seri ous personal injury. No Hands SymbolFailure to keep your hands away from the blade will result in seri ous personal injury. Hot SurfaceTo reduce the risk of injury or damage, avoid contact with any hot surface.
Page 7 of the Ryobi One+ Circular Saw (P500) user manual — SAVE THESE INSTRUCTIONS
Page 7 · cliquer pour agrandir
Page 7

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

SERVICE

Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to the nearest AUTHORIZED SERVICE CENTER for repair. When servic ing, use only identical replacement parts.

WARNING:

The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and, when needed, a full face shield. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked to comply with ANSI Z87.1.

SAVE THESE INSTRUCTIONS

Page 8 of the Ryobi One+ Circular Saw (P500) user manual — PRODUCT SPECIFICATIONS
Page 8 · cliquer pour agrandir
Page 8

FEATURES

PRODUCT SPECIFICATIONS

Cutting Depth at 45° 1-1/8 in.

Motor 18 V DC

Blade Diameter 5-1/2 in.

No Load Speed 4,200 r/min. (RPM)

Blade Arbor 3/8 in.

Laser Guide Class II,

Cutting Depth at 0° 1-9/16 in.

Ryobi One+ Circular Saw (P500) — PRODUCT SPECIFICATIONS diagram (page 8)
Fig. 2
Page 9 of the Ryobi One+ Circular Saw (P500) user manual — PACKING LIST
Page 9 · cliquer pour agrandir
Page 9

FEATURES

KNOW YOUR LASER CIRCULAR SAW See Figure 1.

LOCK-OFF BUTTON The lock-off button reduces the possibility of accidental starting. BEVEL ADJUSTMENT KNOB The bevel adjustment feature allows you to make bevel cuts of 45° and 90º. WIDTH OF CUT SCALE When making straight cross cuts or rip cuts, the scale can be used to measure up to four inches to the right side of the blade. It can be used to measure up to one inch to the left side of the blade. LASER GUIDE The laser guide will generate a red line on the work surface when turned on.

The safe use of this product requires an understanding of the information on the tool and in this operator’s manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules. SWITCH TRIGGER The saw has a conveniently located switch trigger on the underside of the handle. SPINDLE LOCK

The spindle lock allows you to secure the blade when turn ing the blade screw. BLADE WRENCH STORAGE Convenient wrench storage for quick blade changes.

ASSEMBLY

UNPACKING

This product requires assembly.

n Carefully remove the tool and any accessories from the

box. Make sure that all items listed in the packing list are included.

n Inspect the tool carefully to make sure no breakage or

damage occurred during shipping.

n Do not discard the packing material until you have care

fully inspected and satisfactorily operated the tool.

n If any parts are damaged or missing, please call

1-800-525-2579 for assistance.

PACKING LIST

Circular Saw with Laser

5-1/2 in. Blade

Blade Wrench · AAA batteries (2) · Operator’s Manual

Page 10 of the Ryobi One+ Circular Saw (P500) user manual — TO TIGHTEN
Page 10 · cliquer pour agrandir
Page 10

ASSEMBLY

ATTACHING THE BLADE See Figure 2.

SPINDLE LOCK BUTTON

LOWER BLADE GUARD HANDLE

WARNING: A 5-1/2 in. blade is the maximum blade capacity of the saw. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guard, while thicker blades will prevent blade screw from se curing blade on spindle. Either of these situations could result in a serious accident.

SPINDLE

BLADE

45 45 50 50

Remove the battery pack from the saw.

30 30 22 22

n Remove the blade wrench (5 mm hex key) from the stor

age area.

n Depress the spindle lock button and remove the blade

screw and outer blade washer.

INNER BLADE WASHER

OUTER BLADE WASHER

BLADE SCREW

LOWER BLADE

SPINDLE LOCK

GUARD LEVER

n Wipe a drop of oil onto the inner blade washer and outer

blade washer where they contact the blade.

SPINDLE

LOCK SCREW

45 45 50 50

30 30 22 22

TO LOOSEN

n Fit the saw blade inside the lower blade guard and onto

the spindle.

n Replace the outer blade washer.

TO TIGHTEN

n Depress the spindle lock button, then replace the blade

screw. Tighten the blade screw securely by turning it clockwise.

n Position the saw as shown, depress the spindle lock

button, and remove the blade screw by turning it clock wise.

n Return the blade wrench to the storage area.

n Remove the outer blade washer.

n Remove the blade.

REMOVING THE BLADE See Figure 3. Remove the battery pack from the saw.

n Remove the blade wrench from the storage area.

Page 11 of the Ryobi One+ Circular Saw (P500) user manual — BATTERY
Page 11 · cliquer pour agrandir
Page 11

DEPRESS LATCHES TO REMOVE BATTERY PACK

TO INSTALL

APPLICATIONS You may use this tool for the following purposes:

Cutting all types of wood products (lumber, plywood,

BATTERY

PACK

Cross Cutting/Rip Cutting Bevel Cutting Pocket Cutting

This product will accept Ryobi One+ 18 V lithium-ion battery packs and Ryobi One+ 18 V nickel-cadmium battery packs.

For complete charging instructions, refer to the Operator’s Manual for the battery packs and chargers listed in the General Safety Rules.

REMOVING THE BATTERY PACK See Figure 4. n Locate the latches on the side of the battery pack and

INSTALLING THE BATTERY PACK See Figure 4. n Place the battery pack in the saw. Align the raised rib

depress them to release the battery pack from the saw.

on the battery pack with the groove inside the saw, then slide the battery pack into the saw.

n Remove battery pack from your saw.

n Make sure the latches on each side of your battery pack

snap into place and the battery pack is secured in the saw before beginning operation.

paneling)

Page 12 of the Ryobi One+ Circular Saw (P500) user manual — DEPRESS LATCHES TO REMOVE BATTERY PACK
Page 12 · cliquer pour agrandir
Page 12
Ryobi One+ Circular Saw (P500) — DEPRESS LATCHES TO REMOVE BATTERY PACK diagram (page 12)
Fig. 3
Ryobi One+ Circular Saw (P500) — DEPRESS LATCHES TO REMOVE BATTERY PACK diagram (page 12)
Fig. 4

KICKBACK See Figures 5 - 8. Kickback occurs when the blade stalls rapidly and the saw is driven back towards you. Blade stalling is caused by any action which pinches the blade in the wood.

Ryobi One+ Circular Saw (P500) — DEPRESS LATCHES TO REMOVE BATTERY PACK diagram (page 12)
Fig. 5

To guard against kickback, avoid dangerous practices such as the following. Setting blade depth incorrectly. Sawing into knots or nails in workpiece. Twisting the blade while making a cut. Making a cut with a dull, gummed up, or improperly set

blade. Supporting the workpiece incorrectly. Forcing a cut. Cutting warped or wet lumber.

CORRECT BLADE DEPTH SETTING = BLADE EXPOSED 1/4 in.

Operating the tool incorrectly or misusing the tool.

To lessen the chance of kickback, follow these safety prac tices. Keep the blade at the correct depth setting. The depth

setting should not exceed 1/4 in. below the material being cut. Inspect the workpiece for knots or nails before cutting.

Never saw into a knot or nail. Make straight cuts. Always use a straight edge guide

when rip cutting. This helps prevent twisting the blade. Use clean, sharp, and properly set blades. Never make

cuts with dull blades. Support the workpiece properly before beginning a cut. Use steady, even pressure when making a cut. Never

force a cut. Do not cut warped or wet lumber. Hold the saw firmly with both hands and keep your body

in a balanced position so as to resist the forces if kickback should occur.

Ryobi One+ Circular Saw (P500) — DEPRESS LATCHES TO REMOVE BATTERY PACK diagram (page 12)
Fig. 6
Page 13 of the Ryobi One+ Circular Saw (P500) user manual — SWITCH
Page 13 · cliquer pour agrandir
Page 13

SAW BLADES The best of saw blades will not cut efficiently if they are not kept clean, sharp, and properly set. Using a dull blade will place a heavy load on the saw and increase the danger of kickback. Keep extra blades on hand, so that sharp blades are always available. Gum and wood pitch hardened on blades will slow the saw down. Remove saw blade from the saw and use gum and pitch remover, hot water, or kerosene to remove these ac cumulations. DO NOT USE GASOLINE. BLADE GUARD SYSTEM See Figure 9. The lower blade guard attached to your circular saw is there for your protection and safety. Do not alter it for any reason. If it becomes damaged, do not operate the saw until you have the guard repaired or replaced. Always leave guard in operating position when using the saw.

LOWER BLADE GUARD

IS IN UP POSITION WHEN MAKING A CUT

Fig. 9 BLADE EXPOSED ON UNDERSIDE OF WORKPIECE

LOCK-OFF

BUTTON

SWITCH

STARTING/STOPPING THE SAW See Figure 10. To start the saw: Depress the switch trigger.

LOCK-OFF BUTTON See Figure 10. The lock-off button reduces the possibility of accidental starting. The lock-off button is located on the handle above the switch trigger. The lock-off button must be depressed before you pull the switch trigger. The lock resets each time the trigger is released. NOTE: You can depress the lock-off button from either the left or right side.

Always let the blade reach full speed, then guide the saw into the workpiece.

Ryobi One+ Circular Saw (P500) — SWITCH diagram (page 13)
Fig. 7

To stop the saw: Release the switch trigger.

After you release the switch trigger, allow the blade to come to a complete stop. Do not remove the saw from the workpiece while the blade is moving.

Page 14 of the Ryobi One+ Circular Saw (P500) user manual — LASER GUIDE
Page 14 · cliquer pour agrandir
Page 14

ADJUSTING BLADE DEPTH See Figure 11. Always keep correct blade depth setting. The correct blade depth setting for all cuts should not exceed 1/4 in. below the material being cut. More blade depth will increase the chance of kickback and cause the cut to be rough. For more depth of cut accuracy, a scale is located on the upper blade guard. Loosen the depth adjustment knob.

TO RAISE

SAW

Determine the desired depth of cut.

Locate the depth of cut scale on the back of the upper

blade guard.

Hold the base flat against the workpiece and raise or

lower the saw until the indicator mark on bracket aligns with the notch on the blade guard.

BASE ASSEMBLY

Tighten the depth adjustment knob securely.

TO LOWER SAW

TO TIGHTEN

USING THE LASER GUIDE See Figure 12.

DEPTH ADJUSTMENT

TO LOOSEN

KNOB

LASER GUIDE

SWITCH

ON/OFF

Adjust the depth and angle of the cut as needed.

Switch on the laser beam.

Install the battery pack into the tool and start the mo

tor.

30 30 22 22

45 45 50 50

complete stop before turning off the laser.

Page 15 of the Ryobi One+ Circular Saw (P500) user manual — WRONG
Page 15 · cliquer pour agrandir
Page 15

OPERATING THE SAW See Figures 13 - 15. It is important to understand the correct method for operat ing the saw. Refer to the figures in this section to learn the correct and incorrect ways for handling the saw.

45 45 50 50

30 30 22 22

WRONG

To make the best possible cut, follow these helpful hints.

Hold the saw firmly with both hands.

Avoid placing your hand on the workpiece while making

a cut.

Support the workpiece so that the cut (kerf) is always to

your side.

Support the workpiece near the cut.

Clamp the workpiece securely so that the workpiece will

45 45 50 50

not move during the cut.

30 30 22 22

Always place the saw on the workpiece that is supported,

not the “cut off” piece.

Place the workpiece with the “good” side down.

Draw a guideline along the desired line of cut before

beginning your cut.

45 45 50 50

30 30 22 22

WRONG Fig. 15

Page 16 of the Ryobi One+ Circular Saw (P500) user manual — WRONG
Page 16 · cliquer pour agrandir
Page 16

CROSS CUTTING/RIP CUTTING See Figure 16. When making a cross cut or rip cut, align the line of cut with the outer blade guide notch on the base. Since blade thicknesses vary, always make a trial cut in scrap material along a guideline to determine how much, if any, you must offset the guideline to produce an accurate cut. NOTE: The distance from the line of cut to the guideline is the amount you should offset the guide. RIP CUTTING See Figure 17. Use a guide when making long or wide rip cuts with the saw. Secure the workpiece.

Ryobi One+ Circular Saw (P500) — WRONG diagram (page 16)
Fig. 8

Clamp a straight edge to the workpiece using

C-clamps.

Saw along the straight edge to achieve a straight rip

cut.

WIDTH OF CUT SCALE See Figure 18. A width of cut scale has been provided on the base of your saw. When making straight cross cuts or rip cuts, the scale can be used to measure up to four inches to the right side of the blade. It can be used to measure up to one inch to the left side of the blade.

Page 17 of the Ryobi One+ Circular Saw (P500) user manual — LOWER BLADE GUARD
Page 17 · cliquer pour agrandir
Page 17

BEVEL CUTTING See Figures 19 - 21. Align the line of cut with the inner blade guide notch on

BEVEL ADJUSTMENT KNOB

the base when making 45° bevel cuts.

Make a trial cut in scrap material along a guideline to

determine how much you should offset the guideline on the cutting material.

Adjust the angle of the cut to any desired setting between

zero and 51.5°. Refer to “Adjusting the Bevel Setting” next.

BEVEL SCALE

1 45 1 2 3

BLADE GUIDE NOTCH

GUIDELINE

Raise the motor housing end of the saw until you reach

the desired angle setting on the bevel scale.

MOTOR HOUSING

Tighten the bevel adjustment knob securely.

MAKING A BEVEL CUT See Figure 21. Hold the saw firmly with both hands as shown.

2 3 1 45 0

Rest the front edge of the base on the workpiece.

Start the saw and let the blade reach full speed.

Guide the saw into the workpiece and make the cut.

BEVEL SCALE

Release the trigger and allow the blade to come to a

BEVEL ADJUSTMENT

complete stop.

Lift the saw from the workpiece.

KNOB

Fig. 20 BLADE GUIDE NOTCH

2 3 1 45 0

LOWER BLADE GUARD

Page 18 of the Ryobi One+ Circular Saw (P500) user manual — BEVEL ADJUSTMENT KNOB
Page 18 · cliquer pour agrandir
Page 18

POCKET CUTTING See Figure 22.

Release the trigger and allow the blade to come to a

complete stop. Lift the saw from the workpiece. Clear corners out with a hand saw or sabre saw.

Ryobi One+ Circular Saw (P500) — BEVEL ADJUSTMENT KNOB diagram (page 18)
Fig. 9
Ryobi One+ Circular Saw (P500) — BEVEL ADJUSTMENT KNOB diagram (page 18)
Fig. 10

Adjust the bevel setting to zero.

Set the blade to the correct blade depth setting.

Swing the lower blade guard up using the lower blade

guard handle.

Hold the lower blade guard by the handle.

Rest the front of the base flat against the workpiece with

the rear of the handle raised so the blade does not touch the workpiece.

Start the saw and let the blade reach full speed.

Guide the saw into the workpiece and make the cut.

Ryobi One+ Circular Saw (P500) — BEVEL ADJUSTMENT KNOB diagram (page 18)
Fig. 11
Page 19 of the Ryobi One+ Circular Saw (P500) user manual — ADJUSTMENTS
Page 19 · cliquer pour agrandir
Page 19

ADJUSTMENTS

Ryobi One+ Circular Saw (P500) — ADJUSTMENTS diagram (page 19)
Fig. 12
Ryobi One+ Circular Saw (P500) — ADJUSTMENTS diagram (page 19)
Fig. 13

POSITIVE 0° BEVEL STOP See Figure 23. The saw has a positive 0° bevel stop that has been factory adjusted to assure 0° angle of the saw blade when making 90° cuts.

CHECKING POSITIVE 0° BEVEL STOP Place the saw in an upside down position on a work

bench.

Check the squareness of the saw blade to the base of

the saw using a carpenter’s square.

ADJUSTING POSITIVE 0° BEVEL STOP Loosen bevel adjustment knob.

Turn setscrew with hex key and adjust base until it is

square with the saw blade.

Tighten bevel adjustment knob securely.

Ryobi One+ Circular Saw (P500) — ADJUSTMENTS diagram (page 19)
Fig. 14

ADJUSTING THE LASER See Figure 24. NOTE: Draw a pencil line on a scrap workpiece parallel to the long edge of the base as a straight line guide to aid in the adjusting process. Make sure the laser is turned off. Remove the laser cover by lifting it off its base. Turn the laser on. Loosen the screw inside the laser. Rest the front of the base on a scrap workpiece. Adjust the laser beam with the mark on the scrap

workpiece by loosening the screw to the laser aperture and slowly moving the laser guide left or right.

Since blade thicknesses vary, always make a trial cut in

scrap workpiece to ensure an accurate cut. Once alignment is achieved, tighten the screw.

Replace the laser cover.

Check for proper alignment.

Repeat as necessary until the laser is aligned.

Page 20 of the Ryobi One+ Circular Saw (P500) user manual — MAINTENANCE
Page 20 · cliquer pour agrandir
Page 20

MAINTENANCE

GENERAL MAINTENANCE Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

Only the parts shown on the parts list are intended to be repaired or replaced by the customer. All other parts should be replaced at an Authorized Service Center. REPLACING LASER GUIDE BATTERIES See Figure 25. Remove the battery pack from the saw. Make sure the laser is turned off. Remove the laser cover by lifting it off its base. Remove both AAA batteries. Install the two AAA batteries, aligning the positives (+)

with positives (+) and the negatives (-) with negatives (-) as shown on the inside base of the laser. Replace the laser cover. Turn on the laser.

Ryobi One+ Circular Saw (P500) — MAINTENANCE diagram (page 20)
Fig. 15
Page 21 of the Ryobi One+ Circular Saw (P500) user manual — ACCESSORIES
Page 21 · cliquer pour agrandir
Page 21

MAINTENANCE

BATTERIES This product will accept Ryobi One+18V lithium-ion batteriy packs or Ryobi One+ 18 V nickel-cadmium batteriy packs. Length of service from each charging will depend on the type of work you are doing. The batteries for this product have been designed to provide maximum trouble-free life. However, like all batteries, they will eventually wear out. Do not disassemble battery pack and attempt to replace the batteries. Handling of these batteries, especially when wearing rings and jewelry, could result in a serious burn. To obtain the longest possible battery life, we suggest the following:

BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING

To preserve natural resources, please recycle or dispose of batteries properly.

This product uses nickel-cadmium and lithium-ion batteries. Local, state or federal laws may prohibit disposal of batteries in ordinary trash.

Consult your local waste authority for information regarding available recycling and/or disposal options.

For lithium-ion batteries:

WARNING: Upon removal, cover the battery pack’s terminals with heavy-duty adhesive tape. Do not attempt to destroy or disassemble battery pack or remove any of its compo nents. Lithium-ion and nickel-cadmium batteries must be recycled or disposed of properly. Also, never touch both terminals with metal objects and/or body parts as short circuit may result. Keep away from children. Failure to comply with these warnings could result in fire and/or serious injury.

Remove the battery pack from the charger once it is fully

charged and ready for use.

For battery pack storage longer than 30 days:

Store the battery pack where the temperature is below

80°F and away from moisture.

Store battery packs in a 30%-50% charged condition.

Every six months of storage, charge the pack as

normal. For nickel-cadmium batteries:

Remove the battery pack from the charger once it is fully

charged and ready for use.

For battery pack storage longer than 30 days:

Store the battery pack where the temperature is below

80°F.

Store battery packs in a “discharged” condition.

ACCESSORIES

The following recommended accessories are currently available at retail stores:

n 5-1/2 in. Thin Kerf Blade

Li - Ion

Page 22 of the Ryobi One+ Circular Saw (P500) user manual — 983000-496 7-29-10 (REV:06)
Page 22 · cliquer pour agrandir
Page 22

OPERATOR’S MANUAL

5-1/2 in., 18 VOLT LASER CIRCULAR SAW

P500

  • WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
  • lead from lead-based paints,
  • crystalline silica from bricks and cement and other masonry products, and
  • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
  • PARTS AND SERVICE Prior to requesting service or purchasing replacement parts, please obtain your model and serial number from the product data plate.

P500

  • MODEL NUMBER
  • SERIAL NUMBER
  • HOW TO OBTAIN REPLACEMENT PARTS: Replacement parts can be purchased online at <a href="http://www.ryobitools.com" rel="nofollow noopener" target="_blank">www.ryobitools.com</a> or by calling 1-800-525-2579. Replacement parts can also be obtained at one of our Authorized Service Centers.
  • HOW TO LOCATE AN AUTHORIZED SERVICE CENTER: Authorized Service Centers can be located online at <a href="http://www.ryobitools.com" rel="nofollow noopener" target="_blank">www.ryobitools.com</a> or by calling 1-800-525-2579.
  • HOW TO OBTAIN CUSTOMER OR TECHNICAL SUPPORT: To obtain Customer or Technical Support please contact us at 1-800-525-2579.

RYOBI® is a registered trademark of Ryobi Limited used under license.

ONE WORLD TECHNOLOGIES, INC.

1428 Pearman Dairy Road, Anderson, SC 29625 Phone 1-800-525-2579

www.ryobitools.com

983000-496 7-29-10 (REV:06)

Sources

Références et liens

Pages mentionnées dans ce manuel — fabricant, assistance et téléchargements.

Poser une question sur : Ryobi One+ Circular Saw (P500)

Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Aucune question pour l'instant sur le Ryobi One+ Circular Saw (P500)

Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.

Document d'origine

Ryobi One+ Circular Saw (P500) manuel PDF

68 pages·3.4 MB·Scie sans fil·PDF
Cliquez sur une page ci-dessus pour l'ouvrir ici
Page 1 / …
100%
Chargement des pages…