
ARCHITECT ® SERIES II
Use & Care Guide
For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230
or visit our website at www.kitchenaid.com
In Canada, call for assistance, installation and service, call: 1-800-807-6777
or visit our website at www.kitchenaid.ca
ARCHITECT ® SÉRIE II Guide d’utilisation et d’entretien
Au Canada, pour assistance, installation ou service composez le 1-800-807-6777
ou visitez notre site web à www.kitchenaid.ca
Table of Contents/Table des matières 2




Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
– Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
Gas suppliers recommend that you use a gas detector approved by UL or CSA. For more information, contact your gas supplier.
If a gas leak is detected, follow the “What to do if you smell gas” instructions.
State of California Proposition 65 Warnings:

The Anti-Tip Bracket The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without the anti-tip bracket fastened down properly.

A child or adult can tip the range and be killed.
Verify the anti-tip bracket has been properly installed and engaged per installation instructions.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
To verify the anti-tip bracket is installed and engaged:

is used to wipe spills on a hot cooking area, be careful to avoid steam burn. Some cleaners can produce noxious fumes if applied to a hot surface.
RANGE, THE RANGE MUST BE SECURED BY PROPERLY INSTALLED ANTI-TIP DEVICES. TO CHECK IF THE DEVICES ARE INSTALLED PROPERLY, SLIDE RANGE FORWARD, LOOK FOR ANTI-TIP BRACKET SECURELY ATTACHED TO FLOOR OR WALL, AND SLIDE RANGE BACK SO REAR RANGE FOOT IS UNDER ANTI-TIP BRACKET.
escape before removing or replacing food.
pressure may cause container to burst and result in injury.
heat or warm the room. Doing so may result in carbon monoxide poisoning and overheating of the oven.
desired location while oven is cool. If rack must be moved while oven is hot, do not let potholder contact hot heating element in oven.
oven bottom or cover an entire rack with materials such as aluminum foil. Doing so blocks air flow through the oven and may cause carbon monoxide poisoning. Aluminum foil linings may also trap heat, causing a fire hazard.
SURFACES OF OVEN – Heating elements may be hot even though they are dark in color. Interior surfaces of an oven become hot enough to cause burns. During and after use, do not touch, or let clothing or other flammable materials contact heating elements or interior surfaces of oven until they have had sufficient time to cool. Other surfaces of the appliance may become hot enough to cause burns – among these surfaces are oven vent openings and surfaces near these openings, oven doors, and windows of oven doors.
cabinets above a range or on the backguard of a range – children climbing on the range to reach items could be seriously injured.
or unattended in area where the range is in use. They should never be allowed to sit or stand on any part of the range.
should never be worn while using the range.
electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70. In Canada, the range must be electrically grounded in accordance with Canadian Electrical Code. Be sure the range is properly installed and grounded by a qualified technician.
unless specifically recommended in the manual. All other servicing should be referred to a qualified technician.
be stored in an oven or near surface units.
appliance.
use dry chemical or foam-type extinguisher.
or drawers such as stepping, leaning, or sitting on the doors or drawers.
surfaces may result in burns from steam. Do not let potholder touch hot heating elements. Do not use a towel or other bulky cloth.
combustible materials, gasoline, and other flammable vapors and liquids.
Surface units may be hot even though they are dark in color. Areas near surface units may become hot enough to cause burns. During and after use, do not touch, or let clothing or other flammable materials contact surface units or areas near units until they have had sufficient time to cool. Among those areas are the cooktop and surfaces facing the cooktop.
extend beyond the edge of the cooking utensil.
For self-cleaning ranges –
essential for a good seal. Care should be taken not to rub, damage, or move the gasket.
Boilover causes smoking and greasy spillovers that may ignite.
cleaner or oven liner protective coating of any kind should be used in or around any part of the oven.
glass/ceramic, ceramic, earthenware, or other glazed utensils are suitable for range-top service without breaking due to the sudden change in temperature.
and other utensils. Wipe off all excessive spillage before initiating the cleaning cycle.
Adjacent Surface Units – To reduce the risk of burns, ignition of flammable materials, and spillage due to unintentional contact with the utensil, the handle of a utensil should be positioned so that it is turned inward, and does not extend over adjacent surface units.
For units with ventilating hood –
be allowed to accumulate on hood or filter.

This manual covers several different models. The range you have purchased may have some or all of the items listed. The locations and appearances of the features shown here may not match those of your model.

A. Surface burner locator B. Oven display C. Left rear control knob (6000 Btu/h)
D. Left front dual valve TripleTier® flame burner
F. Right front control knob (6000 Btu/h) G. Right rear control knob (12,500 Btu/h)
knob (15,000 Btu/h) E. Electronic oven control


A. Warming drawer B. CleanBake™ Element C. Anti-tip bracket D. Broil element (not shown)
J. Right front surface burner K. Control panel
A. Oven lights B. Full and center broil elements C. Oven cavity sensor D. T.H.E.™ convection fan and element (not visible)
L. Automatic oven light switch/
self-clean latch M. Door gasket
E. Oven vent F. Left front surface burner (dual valve
E. CleanBake™ element (not visible)
N. Model and serial number plate O. Oven door window
TripleTier® flame burner with InstaWok™ Grate on some models) G. Left rear surface burner H. Standard grate
Parts and Features not shown Broiler pan and grid Temperature probe
I. Right rear surface burner
Range Oven Interior

OFF
S
M
M
E
R
Do not let the burner flame extend beyond the edge of the pan.
B
N
R
R
E
R
E
N
R
U
Turn off all controls when not cooking.
R
E
W
O
P
Failure to follow these instructions can result in death or fire.
The TripleTier® Flame Burner (15,000 Btu/h [British Thermal Units]) can provide the highest heat setting and 3 levels of simmer control. It is ideal for cooking large quantities of food or liquid and using large pots and pans.
IMPORTANT: Your cooktop is factory-set for use with Natural gas. If you wish to use LP Gas, an LP Gas Conversion Kit is included with your new range. Models with the TripleTier® Flame Burner will include a TripleTier® Burner LP Gas Conversion Kit and a kit for standard ranges. See the Installation Instructions for details on making this conversion. Electric igniters automatically light the surface burners when control knobs are turned to LITE. Before setting a control knob, place filled cookware on the grate. Do not operate a burner while using empty cookware or without any cookware on the grate. NOTE: Visually check that the burner has lit. If the burner does not ignite, listen for the clicking sound. If you do not hear the igniter click, turn the burner off. Check for a tripped circuit breaker or blown fuse. Check that the control knob is pressed completely down on the valve shaft. If the spark igniter still does not operate, call a trained repair specialist. Proper grounding and polarity are necessary for correct operation of the electric ignition system. If the wall receptacle does not provide correct polarity, the igniters will become grounded and occasionally click, even after the burner has ignited. Contact a trained repair specialist to check the wall receptacle to see whether it is wired with the correct polarity.
To Set: 1. Push in and turn knob counterclockwise to LITE. All surface burners will click. Only the simmer burner with the control knob turned to Lite will produce a flame.
RECOMMENDED USE
HI ■ Start food cooking.
REMEMBER: When range is in use or (on some models) during the Self-Cleaning cycle, the entire cooktop area may become hot.
Power failure In case of prolonged power failure, the surface burners can be lit manually. Hold a lit match near a burner and turn knob counterclockwise to LITE. After burner lights, turn knob to setting.
LO ■ Fry or sauté foods.
Simmer Settings 1. Push in and turn knob counterclockwise to LITE. All surface burners will click. Only the simmer burner with the control knob turned to Lite will produce a flame.

Use the following chart as a guide when setting Simmer Burner heat levels.
LITE ■ Light the burner.
HI ■ Cooking thicker foods such as tomato sauce, chili.
LITE ■ Light the burner.
HI ■ Cooking thicker foods such as tomato sauce, chili.
LO ■ Keep food warm.
LO ■ Keep food warm.
Medium and Small Burner Control
OFF
The TripleTier® Flame Burner (15,000 Btu/h [British Thermal Units]) can provide the highest heat setting and 3 levels of simmer control. It is ideal for cooking large quantities of food or liquid and using large pots and pans.
All of the burner controls provide a range of cooking settings from HI to LO. The medium burner (12,500 Btu/h) provides the high heat setting, and is ideal for cooking medium-sized quantities of food or liquid and using medium-sized pots and pans. The small burners (6,000 Btu/h) are ideal for small quantities of food or liquid and using small pots and pans. The lower power allows more accurate simmer control at the lowest setting.
To Set: 1. Push in and turn knob counterclockwise to LITE. All surface burners will click. Only the simmer burner with the control knob turned to Lite will produce a flame.
To Set: 1. Push in and turn knob counterclockwise to LITE. All surface burners will click. Only the burner with the control knob turned to Lite will produce a flame.
HIGH POWER SETTING
RECOMMENDED USE
HI ■ Start food cooking.
HI ■ Start food cooking.
Medium High between MED and HI
MED (Medium) ■ Hold a slow boil.
LO ■ Fry or sauté foods.
Medium Low between MED and LO
Simmer Settings 1. Push in and turn knob counterclockwise to LITE. All surface burners will click. Only the simmer burner with the control knob turned to Lite will produce a flame.
LO ■ Keep food warm.

Sealed Surface Burners IMPORTANT: Do not obstruct the flow of combustion and ventilation air around the burner grate edges.
A
Always keep the burner cap properly fitted in place when using a surface burner. A clean burner cap will help avoid poor ignition and uneven flames. Always clean the burner cap after a spillover and routinely remove and clean the caps according to the “General Cleaning” section.
B
A
A. Wok supports pointing down (for use
with flat-bottomed cookware) B. Cooktop grate with InstaWok™ Grate
insert (left side of range only) C. Reversible InstaWok™ Grate insert
The TripleTier® Flame Burner with InstaWok™ Grate is a multifunction burner that produces everything from a rapid boil down to a low simmer. The TripleTier® Flame Burner with InstaWok™ Grate is functioned by a dual valve control knob, which controls 2 separate burners. See “TripleTier® Burner with High Power Settings and Low Simmer Settings” in the “Cooktop Controls” section. The InstaWok™ Grate supports 12" to 14" (30.5 cm to 35.6 cm) Wok pans and can be flipped over to become a flat grate for use with flat-bottomed cookware. IMPORTANT: The InstaWok™ Grate must be in place when you are using the TripleTier® Flame Burner.
E
D
A. TripleTier® flame burner caps B. Burner base C. Alignment pins D. Igniter
E. Gas tube opening
To Use the InstaWok™ Grate: 1. Check that the control knob is in the OFF position and the grate is completely cool before handling. 2. Remove grate from cooktop and flip the grate over so that the wok supports are pointing up.
A
B D
E
A. Burner cap B. Burner base C. Alignment pins D. Igniter
E. Gas tube opening
A. Wok supports pointing up B. Cooktop grate with InstaWok™
Grate insert (left side of range only) C. Reversible InstaWok™ Grate insert
Gas must flow freely throughout the gas tube opening for the burner to light properly. Keep this area free of soil and do not allow spills, food, cleaning agents or any other material to enter the gas tube opening. Avoid spillovers by always using a burner cap.
Standard Burner

Cookware IMPORTANT: Do not leave empty cookware on a hot surface cooking area, element or surface burner. Ideal cookware should have a flat bottom, straight sides and a well-fitting lid, and the material should be of medium-to-heavy thickness. Rough finishes may scratch the cooktop or grates. Aluminum and copper may be used as a core or base in cookware. However, when used as a base they can leave permanent marks on the cooktop or grates. Cookware material is a factor in how quickly and evenly heat is transferred, which affects cooking results. A nonstick finish has the same characteristics as its base material. For example, aluminum cookware with a nonstick finish will take on the properties of aluminum. Cookware with nonstick surfaces should not be used under the broiler. Use the following chart as a guide for cookware material characteristics.
Check burner flames occasionally for proper size and shape as shown below. A good flame is blue in color, not yellow. Keep this area free of soil and do not allow spills, food, cleaning agents or any other material to enter the burner ports. TripleTier® Flame Burner

A. ³⁄₄" (19.1 mm) B. ³⁄₈" (9.53 mm) C. Burner ports
Aluminum ■ Heats quickly and evenly.
Cast iron ■ Heats slowly and evenly.
A. 1-1¹⁄₂" (25-38 mm) B. Burner ports
Ceramic or Ceramic glass
To Clean: IMPORTANT: Before cleaning, make sure all controls are off and the oven and cooktop are cool. Do not use oven cleaners, bleach or rust removers. 1. Remove the burner cap from the burner base and clean according to “General Cleaning” section. 2. Clean the gas tube opening with a damp cloth. 3. Clean clogged burner ports with a straight pin as shown. Do not enlarge or distort the port. Do not use a wooden toothpick. If the burner needs to be adjusted, contact a trained repair specialist.
Copper ■ Heats very quickly and evenly.
Earthenware ■ Follow manufacturer’s instructions.
Porcelain enamel-on- steel or cast iron
Stainless steel ■ Heats quickly, but unevenly.
Home Canning When canning for long periods, alternate the use of surface burners between batches. This allows time for the most recently used areas to cool.
A. Incorrect B. Correct
Standard Burner


A. EasyConvect™ conversion B. Convection oven settings C. Oven settings D. Proof bread setting
G. Number pads H. Start (control lock)
M. Stop time
N. Cook time (length of cooking time) O. Self-clean
I. Off J. Options selection pad K. Clock set/start
P. Oven light (on/off) Q. Warming drawer controls
E. Oven display F. Clock/time of day display
L. Timer
Electronic Control Pads When pressing any control pad function on the Electronic Oven Control, use the pad of your finger to press the desired function. Hold down the pad a few seconds, or until the desired function appears in the display. When entering multiple functions within one setting, pause briefly between each control pad command. If a command pad is pressed several times repeatedly, the pad may briefly stop working. Wait a few seconds, and the pad should function again as normal.
Control Lock The Control Lock feature shuts down the control panel pads to avoid unintended use of the oven. The Control Lock feature may be used either when the range is in use or turned off (for example, during cleaning). The Control Lock is preset unlocked, but can be locked. When the control is locked, only the TIMER SET/START, TIMER OFF and OVEN LIGHT pads will function. To Lock/Unlock Control: Before locking, make sure the oven, the Timer and Timed Cooking are off. Press and hold the START pad for 5 seconds until “CONTROL LOCK” appears on the display. Repeat to unlock and remove “CONTROL LOCK” from the display.
Oven Displays When the oven is in use, this display shows the oven temperature, heat source(s) and start time. During Timed Cooking, this display also shows a timed countdown and the stop time (if entered). If “Err” appears on the display, an invalid pad was pressed. Press OFF and retry your entry. When the oven is not in use, this display is blank.
Off The OFF pad stops any oven function except for the Warming Drawer, Clock, Timer and Control Lock.
Clock/Timer Display This is a 12-hour clock. 1. Press CLOCK SET/START. 2. Press number pads to set time of day. 3. Press CLOCK SET/START
Start The START pad begins any oven function except the Timer, Control Lock and Sabbath Mode. If not pressed within 5 seconds after pressing a pad, “START?” will appear on the oven display as a reminder. If not pressed within 5 minutes after pressing a pad, the oven display will return to inactive mode (blank) and the programmed function will be canceled. If a function has been started and a different function is selected, “START?” will appear in the display after 5 seconds. If the START pad is not pressed within 5 seconds, the oven display will return to the active/already started function.
Timer The Timer can be set in minutes and seconds or hours and minutes and counts down the set time. NOTE: The Timer does not start or stop the oven. 1. Press TIMER SET/START. Press again to switch from MIN/SEC and HR/MIN.

The time can be reset during the countdown by repeating the above steps.
Tone Volume High/Low The volume is preset to HIGH, but can be changed to LOW. To change: Press OPTIONS, then 3 for LOW. Press OPTIONS, then 3 again for HIGH.
Options Selection Pad The OPTIONS selection pad allows you to access special functions within the Electronic Oven Control that allow you to customize the product to your needs. These special functions allow you to change the oven temperature between Fahrenheit and Celsius, turn the audible signals and prompts on and off, and adjust the oven calibration. The Dehydrate and Sabbath Mode are also set using the OPTIONS selection pad. To Use: Press OPTIONS. The oven display will scroll through the various options, starting at 1 and ending in 7. You can also press the OPTIONS selection pad and number pad to quickly enter the desired hidden function.
Cooking Time Completion Tones ON/OFF All tones are preset to ON, but can be turned OFF. To change: Press OPTIONS, then 4 to turn tones OFF. To turn tones ON, press OPTIONS again, and then 4.
Dehydrate - Option 5 (on convection models, closed door) Dehydration is a method used to preserve food. Various factors, such as the quality of the fresh food, pretreatment techniques, the size and thickness of the food, and the climate may affect the finished product. During dehydration, heat is used to force out moisture and air circulation is used to carry the moisture away. Refer to a reliable book or source for complete information about dehydrating and preserving foods.
1 Fahrenheit and Celsius conversion
4 Cooking Time Completion Tones On/Off
To Dehydrate: Position the racks according to the following chart. See “Positioning Racks and Bakeware” section for diagram.
6 Oven temperature calibration
*Available only on convection models.
Fahrenheit and Celsius - Option 1 Fahrenheit is the default setting, but setting may be changed to Celsius. To Change: Press OPTIONS, then 1 on the keypad for Celsius. To convert back to Fahrenheit, press OPTIONS, then 1 again on the keypad.
2 2 and 4
3 1, 3 and 5
Tones - Options 2, 3, 4 Tones are audible signals, indicating the following:
Preheat Completion Tone One chime indicates a preheat cycle has been completed.
Option 6 IMPORTANT: Do not use a thermometer to measure oven temperature because opening the oven door during cycling may give incorrect readings. The oven provides accurate temperatures; however, it may cook faster or slower than your previous oven, so the temperature calibration can be adjusted. It can be changed in Fahrenheit or Celsius. A minus sign means the oven will be cooler by the displayed amount. The absence of a minus sign means the oven will be warmer by the displayed amount.
Timer Completion Tones Three chimes sound when the timer reaches zero. This can occur when using the timer for functions other than cooking.
Cooking Time Completion Tones Three beeps indicate the end of a cooking cycle.
All Tones ON/OFF All tones are preset to ON, but can be turned OFF. To change: Press OPTIONS, then 2 to turn tones OFF. To turn tones ON, press OPTIONS again, and then 2.

Use the following chart as a guide.
ADJUSTMENT °F (AUTOMATIC °C CHANGE)
COOKS FOOD
10°F (5°C) ...a little more
20°F (10°C) ...moderately more
30°F (15°C) ...much more
Do not let food sit in oven more than one hour before or after cooking.
-10°F (-5°C) ...a little less
Doing so can result in food poisoning or sickness.
-20°F (-10°C) ...moderately less
-30°F (-15°C) ...much less
To Adjust Oven Temperature Calibration: 1. Press OPTIONS, and then 6 to set the calibration. 2. Press 3 to increase the temperature, or press 6 to decrease the temperature. 3. Press START to end calibration.
Sabbath Mode - Option 7 The Sabbath Mode sets the oven to remain on in a bake setting until turned off. A timed Sabbath Mode can also be set to keep the oven on for only part of the Sabbath. When the Sabbath Mode is set, only the number and start pads will function, no tones will sound, and the displays will not show messages or temperature changes. The heat sources icons will appear lit on the oven display throughout the Sabbath Mode. When the oven door is opened or closed, the oven light will not turn on or off and the heating elements will not turn on or off immediately. If a power failure occurs when the Sabbath Mode is set, the oven will remain Sabbath Mode compliant but will no longer be actively cooking. The “ON” indicator will no longer be illuminated. Press OFF to return to normal operating mode (non-Sabbath Mode compliant, not cooking).
5. Press OPTIONS, and then press number pad 7. “SABBATH MODE” will appear on the display. 6. When the stop time is reached, the oven will automatically turn off. The oven control will remain Sabbath Mode compliant until the OFF button is pressed. Temperature Change The oven temperature can be changed when the oven(s) are in the Sabbath Mode. No tones will sound, and the display will not change. The heating elements will not turn on or off for a random time, anywhere from 16 to 24 seconds. It may take up to ½ hour for the oven to change temperature. Number pads 1 through 0 represent temperatures. Use the following chart as a guide.
1 170°F (77°C)
To Activate: IMPORTANT: Before the Sabbath Mode can be regularly set, the oven must first be enabled with a one time only setup. 1. Open the oven door. 2. Press OFF. 3. Press the number pads 7, 8, 9, 6, in this order. 4. Press START to activate. “SABBATH ENABLED” will appear on the display.
3 225°F (107°C)
4 250°F (120°C)
5 300°F (149°C)
6 325°F (163°C)
7 350°F (177°C)
9 400°F (204°C)
To Deactivate: The oven can be disabled of the ability to set the Sabbath Mode by repeating the steps in the previous “To Activate” section. When disabled, the Sabbath Mode cannot be regularly set until re-enabled.
To Change Temperature: 1. Press the number pad from the chart. 2. Press START.
Warming Drawer Operation During Sabbath Mode The warming drawer may be set for use during Sabbath Mode. This is accomplished by pressing the WARMING DRAWER ON key (continue pressing until desired temperature level is displayed) before the oven is placed into its Sabbath Mode compliant state. See “To Regularly Set, Untimed” in this section for instructions on placing the oven into its Sabbath Mode compliant state. Once the oven is in its Sabbath Mode compliant state, the warming drawer cannot be turned on or off and its temperature cannot be changed until the oven is returned to its normal operating state (non-Sabbath Mode compliant state, not cooking) by pressing the OFF key.
Food Poisoning Hazard

Odors and smoke are normal when the oven is used the first few times, or when it is heavily soiled. IMPORTANT: The health of some birds is extremely sensitive to the fumes given off. Exposure to the fumes may result in death to certain birds. Always move birds to another closed and well- ventilated room. NOTE: This oven automatically adjusts for 208V operation without affecting cooking performance. Preheat times may be longer.
Meat Thermometer On models without a temperature probe, use a meat thermometer to determine whether meat, poultry and fish, are cooked to the desired degree of doneness. The internal temperature, not appearance, should be used to determine doneness. A meat thermometer is not supplied with this appliance. Follow manufacturer's directions for using a meat thermometer.
Aluminum Foil IMPORTANT: To avoid permanent damage to the oven bottom finish, do not line the oven bottom with any type of foil or liner.
Bakeware The bakeware material affects cooking results. Follow manufacturer’s recommendations and use the bakeware size recommended in the recipe. Use the following chart as a guide.
Use an oven mitt to remove temperature probe.
Do not touch broil element.
RECOMMENDATIONS
Failure to follow these instructions can result in burns.
The temperature probe accurately measures the internal temperature of meat, poultry and casseroles with liquid and should be used in determining the doneness of meat and poultry. It should not be used during full and center broiling, convection broiling, dehydrating or proofing bread. Always unplug and remove the temperature probe from the oven when removing food.
Dark aluminum and other bakeware with dark, dull and/or nonstick finish
To Use: Before using, insert the probe into the center of the thickest portion of meat or into the inner thigh or breast of poultry, away from fat or bone at an angle as shown in following diagram. Place food in oven and connect the temperature probe to the jack. Keep probe as far away from heat source as possible. Close oven door.
Insulated cookie sheets or baking pans
A. Temperature probe jack B. Temperature probe
Ovenproof glassware, ceramic glass or ceramic

FOOD RACK POSITION*
Large roasts, turkeys, angel food, bundt cakes, quick breads, pies
“Lo” will appear as the probe temperature until the internal temperature of the food reaches 130°F (54°C) or if the probe is unplugged. Then the display will show the temperature increasing in 1°F increments.
Yeast breads, casseroles, meat and poultry
Cookies, biscuits, muffins, cakes 2 or 3
When the set probe temperature is reached, the oven will shut off automatically and “Cooking Complete” will appear on the oven display.
*On models with the CleanBake™ feature, foods may be placed on a lower rack position. Convection Cooking
If enabled, end-of-cycle tones will sound.
RACK POSITION(S)
To Change Probe Temperature, Oven Setting: Press OFF, then repeat previous steps. After cooking, unplug the probe and remove food from oven. The probe symbol will remain lit until the probe is unplugged from the probe jack. See “General Cleaning” section to clean probe.
Convection Bake 1 1, 2 or 3
Convection Bake 2 1 or 2 and 4
Convection Bake 3 1, 3 and 5
Convection Roast 1 1, 2 or 3
Convection Broil 1 3 or 4
BAKEWARE To cook food evenly, hot air must be able to circulate. For traditional cooking, allow 2" (5 cm) of space around bakeware and oven walls. For convection cooking, allow 1" (2.5 cm) of space around bakeware and oven walls. Use the following chart as a guide.
POSITION ON RACK
1 Center of rack.
2 Side by side or slightly staggered.
A. Oven vent
3 or 4 Placement that gives best result. Make sure that no bakeware piece is directly over another.
The oven vent should not be blocked or covered since it allows the release of hot air and moisture from the oven. Blocking or covering the vent will cause poor air circulation, affecting cooking and cleaning results. Do not set plastics, paper or other items that could melt or burn near the oven vent.
Bake The BAKE function is ideal for baking, roasting or heating foods. During baking or roasting, the bake and broil elements will cycle on and off in intervals to maintain oven temperature. If the oven door is opened during baking or roasting, the broil element will turn off immediately and the bake element will turn off in 30 seconds to 2 minutes. They will come back on once the door is closed.
Positioning Racks and Bakeware IMPORTANT: To avoid permanent damage to the porcelain finish, do not place food or bakeware directly on the oven door or bottom.
To Bake or Roast: Before baking and roasting, position racks according to the “Positioning Racks and Bakeware” section. For baking, allow the range to preheat before placing food in the oven. When roasting, it is not necessary to wait for the oven to preheat before putting food in, unless recommended in the recipe. 1. Press BAKE once for 350°F (177°C), or press the number pads to enter the desired temperature. 2. Press START. “Preheating” will show in the display until the set temperature is reached.
To move a rack, pull it out to the stop position, raise the front edge, then lift out. Use the following illustration and charts as a guide.
1 2 3 4 5
“Lo” will also appear in the display if the actual oven temperature is under 170°F (77°C).
When the actual oven temperature reaches 170°F (77°C), the oven display will show the oven temperature increasing in 1-degree increments.
When the set temperature is reached, if on, 1 tone will sound.
1 or 2

BROILING CHART For best results, place food 3" (7 cm) or more from the broil element. Times are guidelines only and may need to be adjusted for individual tastes. Recommended rack positions are numbered from the bottom (1) to the top (4). For diagram, see the “Positioning Racks and Bakeware” section.
Broil Broiling uses direct radiant heat to cook food. There are 2 broiling choices, Full Broil and Center Broil. Full Broil uses both top elements for maximum browning coverage of foods. Center Broil uses the inner element for browning coverage of a smaller area.
TEMP. TOTAL TIME MIN.
If you would like to purchase a broiler pan, one may be ordered. See “Assistance or Service” section to order.
Steak 1" (2.5 cm) thick medium rare medium well-done
Steak 1¹⁄₂" (3.8 cm) thick rare medium
Ground meat patties* 1" (2.5 cm) thick well-done 4 500°F (260°C) 16-18
Pork chops 1" (2.5 cm) thick 4 450°F (232°C) 25-28
Ham slice [precooked] ¹₂" (1.25 cm) thick 1" (2.5 cm) thick 4 4 500°F (260°C)
Before broiling, position rack according to the Broiling Chart. It is not necessary to preheat the oven before putting food in unless recommended in the recipe. Position food on grid in the broiler pan, then place it in the center of the oven rack. Close the door to ensure proper broiling operation.
Lamb chops 1" (2.5 cm) thick 4 400°F (204°C) 18-20
To Broil: 1. Press BROIL once for FULL BROIL or twice for CENTER BROIL. Choose Full Broil when broiling larger amounts of food with both broil elements. Choose Center Broil when broiling smaller amounts of food with only the inner broil element.
Chicken bone-in pieces 3 500°F (260°C) 32
Fish ¹₂" (1.25 cm) thick 1" (2.5 cm) thick 3 3 350°F (177°C)
*Place up to 9 patties, equally spaced, on broiler grid.
Variable Temperature Broiling Changing the temperature when Variable Temperature Broiling allows more precise control when cooking. The lower the temperature, the slower the cooking. Thicker cuts and unevenly shaped pieces of meat, fish and poultry may cook better at lower broiling temperatures.
(on some models) In a convection oven, the fan-circulated hot air continually distributes heat more evenly than the natural movement of air in a standard thermal oven. This movement of hot air helps maintain a consistent temperature throughout the oven, cooking foods more evenly, crisping surfaces while sealing in moisture and yielding crustier breads. Most foods can be cooked by lowering cooking temperatures 25°F to 50°F (14°C to 28°C), and cooking time can be shortened by as much as 30 percent, especially for large turkeys and roasts.
To Use: 1. Close oven door. 2. Press BROIL once for FULL BROIL or twice for CENTER BROIL. 3. Press the number pads to set a temperature between 300°F and 500°F (149°C to 260°C). 4. Press START. The temperature can be changed after this step. Press the number pads to reset the temperature, then press START.

(on some models) Convection Bake can be used to bake and cook foods on single or multiple racks. It is helpful to stagger items on the racks to allow a more even flow of heat. If the oven is full, extra cooking time may be needed. When cooking an oven meal with several different types of foods, be sure to select recipes that require similar temperatures. Cookware should sit in the oven with at least 1" (2.5 cm) of space between the cookware and the sides of the oven. Allow the range to preheat before placing food in the oven. During convection baking preheat, the broil elements and the bake element all heat the oven cavity. After preheat, the convection element will cycle on and off in intervals to maintain oven temperature, while the fan constantly circulates the hot air. If the oven door is opened during convection baking or preheating, the convection element and fan will turn off immediately. They will come back on once the door is closed.
Use an oven mitt to remove temperature probe.
Do not touch broil element.
Failure to follow these instructions can result in burns.
To Convection Bake: Before convection baking, position racks according to the “Positioning Racks and Bakeware” section. 1. Press CONVECT BAKE. Press the number pads to enter a temperature other than 325°F (163°C). The convection bake range can be set between 170°F and 500°F (77°C and 260°C).
(on some models) Convection cooking temperatures and times can differ from those of standard cooking. Depending upon the selected category, EasyConvect™ conversion automatically may reduce the standard recipe temperature and/or time you input for convection cooking. Foods are grouped into 3 general categories. Choose the category most appropriate for the food to be cooked. To ensure optimal cooking results, the oven will prompt a food check at the end of a non-delayed cook time. Use the following chart as a guide.
“Lo” will also appear in the display if the actual oven temperature is under 170°F (77°C).
MEATS Baked potatoes, Chicken: whole and pieces Meat loaf, Roasts: pork, beef and ham (Turkey and large poultry are not included because their cook time varies.)
When the actual oven temperature reaches 170°F (77°C), the oven display will show the oven temperature increasing in 1-degree increments.
When the set temperature is reached, if on, 1 tone will sound.
(on some models) Convection Roast can be used to roast meat and poultry, and bake foods, such as yeast breads, pies, loaf, bundt and tube cakes on a single rack. During convection roasting, the bake and broil elements will cycle on and off in intervals to maintain oven temperature, while the fan constantly circulates the hot air. If the oven door is opened during convection roasting, the broil element and convection fan will turn off immediately and the bake element will turn off within 2 minutes. They will come back on once the door is closed.
To Use: When using convection temperature conversion for BAKED GOODS and OTHER FOODS, allow the oven to preheat before placing food in the oven. 1. Press MEATS, BAKED GOODS or OTHER FOODS. 2. Press number pads to enter standard cook temperature. 3. Press number pads to enter standard cook time. 4. Press START. “CHECK FOOD AT” and the stop time will appear on the oven display, after preheating is complete.
To Convection Roast: Before convection roasting, position racks according to the “Positioning Racks and Bakeware” section. It is not necessary to wait for the oven to preheat before putting food in, unless recommended in the recipe. Use the roasting rack on top of the broiler pan and grid. This holds the food above the grid and allows air to circulate completely around all surfaces.
When the stop time is reached, end-of-cycle tones will sound if enabled. Open the door and check food.
Burn Hazard

If you would like to purchase a Broiler Pan Kit, one may be ordered. See “Assistance or Service” section to order. 1. Press CONVECT ROAST. Press the number pads to enter a temperature other than 325°F (162°C). The convection roast range can be set between 170°F and 500°F (77°C and 260°C).
COOK TIME (min. per 1 lb [454 g])
OVEN TEMP. INTERNAL FOOD TEMP.
Lamb, Rack Position 2
Leg, Shoulder Roast medium well-done
“Lo” will also appear in the display if the actual oven temperature is under 170°F (77°C).
Chicken*, Rack Position 2
When the actual oven temperature reaches 170°F (77°C), the oven display will show the oven temperature increasing in 1-degree increments.
Whole 3-5 lbs (1.5-2.2 kg) 5-7 lbs (2.2-3.1 kg)
180°F (82°C)
When the set temperature is reached, if on, 1 tone will sound.
180°F (82°C)
Turkey*, Rack Positions 1 or 2
COOK TIME (min. per 1 lb [454 g])
OVEN TEMP. INTERNAL FOOD TEMP.
13 lbs and under (5.85 kg) Over 13 lbs (5.85 kg)
180°F (82°C)
Beef, Rack Position 2
180°F (82°C)
Rib Roast rare medium well-done Rib Roast (boneless) rare medium well-done Rump, Sirloin Tip Roast rare medium well-done Meat Loaf
Cornish Game Hens*, Rack Position 2 or 3
300°F (149°C)
1-1.5 lbs (0.5-0.7 kg) 50-60 325°F (163°C) 180°F (82°C)
*Do not stuff poultry when convection roasting.
300°F (149°C)
Convection Broil
(on some models) Convection Broil is ideal for cooking foods such as thinner cuts of meat; filets of fish; boneless, skinless chicken; vegetables and garlic bread. During convection broiling, the broil elements will cycle on and off in intervals to maintain oven temperature, while the fan constantly circulates the hot air. The circulating air creates a seal on all sides of the food so that turning of foods is often not necessary. The temperature is preset at 450°F (232°C), but can be changed to a different temperature. Cooking times will vary depending on the rack position and temperature and may need to be adjusted. If the oven door is opened during convection broiling, the broil elements and fan will turn off after 30 seconds. They will come back on once the door is closed.
20-25 25-30 30-35 20-25
300°F (149°C)
325°F (163°C)
Veal, Rack Position 2
Loin, Rib, Rump Roast medium well-done
Pork, Rack Position 2
To Convection Broil: Before convection broiling, see “Broil” section for general broiling guidelines. Position rack. Allow the oven to preheat for 5 minutes. Position food on the unheated grid on the broiler pan, then place it in the center of the oven rack with the longest side parallel to the door. Close the door. 1. Press CONVECT BROIL. Press the number pads to enter a temperature other than 500°F (260°C). The convection broil range can be set between 300°F and 500°F (149°C and 260°C).
Loin Roast (boneless) Shoulder Roast
325°F (163°C)
325°F (163°C)
Ham, Rack Position 2
Fresh (uncooked) Fully Cooked
160°F (71°C)
300°F (149°C)
160°F (71°C)
20-25 25-30 30-35 · 22-25 27-30 32-35

To Set a Delay Cooking Time: Before setting, make sure the clock is set to the correct time of day. See “Clock/Timer Display” section. 1. Press BAKE, CONVECT BAKE or CONVECT ROAST. Press the number pads to enter a temperature other than the one displayed.
(on some models) Proofing bread prepares the dough for baking by activating the yeast. Follow the recipe directions as a guide.
To Proof: Before first proofing, place the dough in a lightly greased bowl and cover loosely with wax paper, coated with shortening. Place on rack guide 2 and close the oven door. 1. Press BREAD PROOF. The display will show 100°F (38°C). 2. Press START. Let the dough rise until nearly doubled in size, checking after 20-25 minutes. Proofing time may vary depending on dough type and quantity.
“DELAY” and the stop time will also appear on the oven display.
When the start time is reached, the oven will automatically turn on. The cook time countdown will appear on the oven display.
On some models, the set temperature and minute time countdown will appear on the oven display.
When the stop time is reached, the oven will shut off automatically, and end-of-cycle tones will sound.
Warming Drawer
Do not let food sit in oven more than one hour before or after cooking.
Doing so can result in food poisoning or sickness.
Do not let food sit for more than one hour before or after cooking.
Timed Cooking allows the oven(s) to cook for a set length of time. Delay Cooking allows the oven(s) to be set to turn on at a certain time of day, Delay start should not be used for food such as breads and cakes because they may not bake properly. Timed Cooking is available on most cycles including: Bake, Convect Bake, Convect Roast, EasyConvect™ Conversion, Bread Proof, and Keep Warm. Delay Cooking is available on the Bake, Convect Bake, and Convect Roast cycles.
Doing so can result in food poisoning or sickness.
The Warming Drawer is ideal for keeping hot cooked foods at serving temperature. It may also be used for warming breads and pastries. Different types of food may be placed in the warming drawer at the same time. For smaller quantities of foods, or foods containing eggs, do not hold longer than 30 minutes. Food must be at serving temperature before being placed in the warming drawer. Breads, pastries, and fruit pies may be heated from room temperature on the HI setting. Remove food from plastic bags and place in oven-safe container. Cover foods with a lid or aluminum foil. Do not cover with plastic wrap. Empty serving dishes and ovenproof dishes can be heated while the warming drawer is preheating. Do not place food to be warmed directly on warming drawer surface.
To Set a Cook Time: 1. Press BAKE, CONVECT BAKE, CONVECT ROAST, BROIL, CONVECT BROIL, or BREAD PROOF. Press the number pads to enter a temperature other than the one displayed.
To Use: 1. Place cooked food(s) in warming drawer. 2. Press WARMING DRAWER ON button. “WARM-LOW” will appear on the display.
When the stop time is reached, the oven will shut off automatically, and end-of-cycle tones will sound.
To change the temperature setting, press WARMING DRAWER ON again. Each press of the WARMING DRAWER ON button will increase the temperature setting. Setting may be changed at any time.
“WARM DRAWER ON” will appear on the display after 5 seconds.
Food Poisoning Hazard · Food Poisoning Hazard

Warming Drawer Settings: The warming drawer is preset for a “low” temperature, but can be changed by pressing WARMING DRAWER ON additional times. Use the following chart as a guide when selecting a different temperature other than “Low.”
Fish Pieces Breaded Battered
SETTINGS TEMPERATURES
LOW 100°F (38°C)
MED LOW (Medium Low) 140°F (60°C)
MED (Medium) 160°F (71°C)
MED HI (Medium High) 180°F (88°C)
HI (High) 195°F (91°C)
Pastries Prepackaged, baked Prepackaged, frozen
Warming Drawer Temperature Chart Different foods require different settings in order to maintain the ideal serving temperature. Use the following chart as a guide.
Pie Single Crust Double Crust
LOW LOW
Potatoes, Baked MED HI
Chicken Boneless, Breaded Nuggets
Roast, Boneless MED HI
Roasted Chicken MED HI
Dinner Plate (1) Salisbury Steak, Mashed Potatoes, Corn HI
Do not touch the oven during the Self-Cleaning cycle.
Keep children away from oven during Self-Cleaning cycle.
Failure to follow these instructions can result in burns.
IMPORTANT: The health of some birds is extremely sensitive to the fumes given off during the Self-Cleaning cycle. Exposure to the fumes may result in death to certain birds. Always move birds to another closed and well-ventilated room. Self-clean the oven before it becomes heavily soiled. Heavy soil results in longer cleaning and more smoke. Keep the kitchen well-ventilated during the Self-Cleaning cycle to help get rid of heat, odors, and smoke. Do not block the oven vent(s) during the Self-Cleaning cycle. Air must be able to move freely. Depending on your model, see “Oven Vent” or “Oven Vents” section. Do not clean, rub, damage or move the oven door gasket. The door gasket is essential for a good seal.

How the Cycle Works IMPORTANT: The heating and cooling of porcelain on steel in the oven may result in discoloring, loss of gloss, hairline cracks and popping sounds. The Self-Cleaning cycle uses very high temperatures, burning soil to a powdery ash. The oven is preset for a 2 hour 30 minute clean cycle; however, the time can be changed. There are 5 levels of clean. Suggested clean times are 2 hours 30 minutes for light soil and between 3 hours 30 minutes to 4 hours 30 minutes for average to heavy soil. Use the following chart as a guide to determine the desired cleaning level.
When the start time is reached, “LOCKING DOOR” will appear in the display. When the door locks, self-clean will start and “OVEN IS CLEANING” then, “DOOR LOCKED” will appear in the display.
The door will not unlock until the oven cools.
When the cycle is complete and the oven cools, “SELF CLEAN COMPLETE” will appear on the oven display.
To Stop Self-Clean anytime: Press OFF. If the oven temperature is too high, the door will remain locked. It will not unlock until the oven cools. If the oven temperature is too high after self-cleaning, then “LOCKED” will appear on the display until the oven completely cools.
TOTAL CLEANING TIME (includes a 30 minute cool down time)
1 (Quick) 2 hours 30 minutes
General Cleaning IMPORTANT: Before cleaning, make sure all controls are off and the oven and cooktop are cool. Always follow label instructions on cleaning products. Soap, water and a soft cloth or sponge are suggested first unless otherwise noted.
3 (Regular) 3 hours 30 minutes
5 (Maxi) 4 hours 30 minutes
Once the oven has completely cooled, remove ash with a damp cloth. To avoid breaking the glass, do not apply a cool damp cloth to the inner door glass before it has completely cooled. The oven light will not work during the Self-Cleaning cycle.
EXTERIOR PORCELAIN ENAMEL SURFACES (on some models)
Food spills containing acids, such as vinegar and tomato, should be cleaned as soon as the entire range is cool. These spills may affect the finish. Cleaning Method:
To Self-Clean: Before self-cleaning, make sure the door is closed completely or it will not lock and the cycle will not begin. 1. Press SELF CLEAN. To set a clean time other than 3 hours 30 minutes, press SELF CLEAN until the desired time is reached. The clean time can be set between 2 hours 30 minutes and 4 hours 30 minutes. 2. Press START. “LOCKING DOOR” will appear on the display as will the clean time, start time and stop time. When the door locks, self- clean will start and “OVEN IS CLEANING” then, “DOOR LOCKED” will appear in the display.
Gently clean around the model and serial number plate because scrubbing may remove numbers.
STAINLESS STEEL (on some models)
The door will not unlock until the oven cools.
When the cycle is complete and the oven cools, “SELF CLEAN COMPLETE” will appear in the oven display.
To Delay Start Self-Clean: Before delay starting Self-Clean, make sure the clock is set to the correct time of day. See “Clock/Timer Display” section. Also, make sure the door is closed completely or it will not lock and the cycle will not begin. 1. Press SELF CLEAN. To set a clean time other than 3 hours 30 minutes, press SELF CLEAN until the desired time is reached. The clean time can be set between 2 hours 30 minutes and 4 hours 30 minutes. 2. Press STOP TIME. 3. Press the number pads to enter the time of day to stop. 4. Press START. The start time is automatically calculated and displayed along with the clean time and stop time. “DELAY” will also appear on the display.
Food spills containing acids, such as vinegar and tomato, should be cleaned as soon as the cooktop, grates and caps are cool. These spills may affect the finish. To avoid chipping, do not bang grates and caps against each other or hard surfaces such as cast iron cookware. Do not reassemble caps on burners while wet. Do not clean in the Self-Cleaning cycle. Do not clean in dishwasher. Cleaning Method:
Clean as soon as cooktop, grates and caps are cool.
2 3 hours · 4 4 hours

WARMING DRAWER (on some models)
Make sure drawer is cool and empty before cleaning. Cleaning Method:
To avoid damage to the cooktop controls, do not use steel wool, abrasive cleansers or oven cleaner. To avoid damage, do not soak knobs. When replacing knobs, make sure knobs are in the Off position. Cleaning Method:
Oven Light(s) The oven light is a standard 15-watt appliance bulb. It will come on when the oven door is opened. The light will not work during the Self-Cleaning cycle (on some models). On some models, when the oven door is closed, press OVEN LIGHT to turn the light on or off.
Pull knobs straight away from control panel to remove.
To Replace: Before replacing bulb, make sure the oven and cooktop are cool and the control knobs are off. 1. Unplug range or disconnect power. 2. Turn the glass bulb cover in the back of the oven counterclockwise to remove.
Cleaning Method:
Apply glass cleaner to soft cloth or sponge, not directly on panel.
To avoid damage to the control panel, do not use abrasive cleaners, steel-wool pads, gritty washcloths or abrasive paper towels. Cleaning Method:
Apply glass cleaner to soft cloth or sponge, not directly on panel.
Oven Door For normal range use, it is not suggested to remove the oven door. However, if removal is necessary, make sure the oven is off and cool. Then, follow these instructions. The oven door is heavy.
Do not use oven cleaners. Food spills should be cleaned when oven cools. At high temperatures, foods react with porcelain and staining, etching, pitting or faint white spots can result. Cleaning Method:
To Remove: 1. Open oven door all the way. 2. Flip up the hinge latch on each side.
See “Self-Cleaning Cycle” first.
Cleaning Method:
See “Self-Cleaning Cycle” first. Remove racks or they will discolor and become harder to slide. If this happens, a light coating of vegetable oil applied to the rack guides will help them slide.
STORAGE DRAWER (on some models)
Make sure drawer is cool and empty before cleaning. For more information, see “Storage Drawer” section. Cleaning Method:
Sealed Burner models

To Replace: 1. Insert both hanger arms into the door.
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.

(on some models) Remove all items from inside the warming drawer, and allow the warming drawer to cool completely before attempting to remove the drawer.
Failure to follow these instructions can result in death, fire, or electrical shock.
To Remove: 1. Open drawer to its fully open position. 2. Locate the black loops on both sides of the drawer.
A. Loop
To Replace: 1. Align the drawer glides with the receiving guides.

Oven burner flames are yellow or noisy
Noises that may be heard during the Bake and Broil operations: Whooshing, Poof, Clicking, Snaps, Pop These sounds are normal operational noises that can be heard each time the Bake or Broil burners ignite during the cycle.
Burner sparks but does not light
Oven will not operate

Before calling for assistance or service, please check “Troubleshooting.” It may save you the cost of a service call. If you still need help, follow the instructions below. When calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond to your request.
Accessories U.S.A. To order accessories, call the KitchenAid Customer eXperience Center toll free at 1-800-442-9991 and follow the menu prompts. Or visit our website at www.kitchenaid.com/ cookingaccessories. Portable appliances, bakeware, cookware, gadgets and textiles are also available.
If you need replacement parts If you need to order replacement parts, we recommend that you use only factory specified parts. These factory specified parts will fit right and work right because they are made with the same precision used to build every new KITCHENAID® appliance. To locate factory specified parts in your area, call us or your nearest KitchenAid designated service center.
KitchenAid® Stainless Steel Cleaner and Polish (stainless steel models) Order Part Number 4396920
KitchenAid® Stainless Steel Wipes (stainless steel models) Order Part Number 8212510
In the U.S.A. Call the KitchenAid Customer eXperience Center toll free: 1-800-422-1230. Our consultants provide assistance with:
Cooktop Cleaner (porcelain or glass cooktop surfaces) Order Part Number 31464
Cooktop Protectant (porcelain or glass cooktop surfaces) Order Part Number 31463
Gas Grate/Drip Pan Cleaner Order Part Number 31617
Brick Pizza Stone Order Part Number 4378577
To locate the KitchenAid designated service company in your area, you can also look in your telephone directory Yellow Pages.
Broiler Pan and Roasting Rack Order Part Number W10123240 www.kitchenaid.com/broilerpan
For further assistance If you need further assistance, you can write to KitchenAid with any questions or concerns at:
Rear Filler Strip Assembly Order Part Number W10113902A Black Order Part Number W10113903A White Order Part Number W10113904A Biscuit
KitchenAid Brand Home Appliances Customer eXperience Center 553 Benson Road Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.

In Canada Call the KitchenAid Canada Customer eXperience Centre toll free: 1-800-807-6777. Our consultants provide assistance with:
KitchenAid® Stainless Steel Wipes (stainless steel models) Order Part Number 8212510
Cooktop Cleaner (porcelain or glass cooktop surfaces) Order Part Number 31464B
Cooktop Protectant (porcelain or glass cooktop surfaces) Order Part Number 31463B
For further assistance If you need further assistance, you can write to KitchenAid Canada with any questions or concerns at:
Gas Grate/Drip Pan Cleaner Order Part Number 31617B
Customer eXperience Centre KitchenAid Canada 200 - 6750 Century Ave. Mississauga, Ontario L5N 0B7
Brick Pizza Stone Order Part Number 4378577
Broiler Pan and Roasting Rack Order Part Number W10123240 www.kitchenaid.com/broilerpan
Please include a daytime phone number in your correspondence.
Rear Filler Strip Assembly Order Part Number W10113902A Black Order Part Number W10113903A White Order Part Number W10113904A Biscuit
To order accessories, visit our website at www.kitchenaid.com/ cookingaccessories. Portable appliances, bakeware, cookware, gadgets and textiles are also available.
KitchenAid® Stainless Steel Cleaner and Polish (stainless steel models) Order Part Number 4396920
LIMITED WARRANTY For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, KitchenAid brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter “KitchenAid”) will pay for Factory Specified Parts and repair labor to correct defects in materials or workmanship. Service must be provided by a KitchenAid designated service company. This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in the country in which it was purchased. Outside the 50 United States and Canada, this limited warranty does not apply. Proof of original purchase date is required to obtain service under this limited warranty.
SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CERTAIN COMPONENT PARTS In the second through fifth years from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, KitchenAid will pay for Factory Specified Parts for the following components if defective in materials or workmanship:
SECOND THROUGH TENTH YEAR LIMITED WARRANTY ON STEAM-ASSIST OVEN CAVITY AND DOORS In the second through tenth years from date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, KitchenAid will pay for Factory Specified Parts for the porcelain oven cavity/inner door if the part rusts through due to defects in materials or workmanship.

ITEMS EXCLUDED FROM WARRANTY This limited warranty does not cover: 1. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair house fuses, or to correct house wiring or plumbing. 2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty coverage. 3. Repairs when your major appliance is used for other than normal, single-family household use or when it is used in a manner that is contrary to published user or operator instructions and/or installation instructions. 4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved by KitchenAid. 5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage results from defects in materials or workmanship and is reported to KitchenAid within 30 days from the date of purchase. 6. Costs associated with the removal from your home of your major appliance for repairs. This major appliance is designed to be repaired in the home and only in-home service is covered by this warranty. 7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance. 8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an authorized KitchenAid servicer is not available. 9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with published installation instructions. 10. Major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined. This warranty is void if the factory applied serial number has been altered or removed from your major appliance. The cost of repair or replacement under these excluded circumstances shall be borne by the customer.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. KITCHENAID SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.
If outside the 50 United States and Canada, contact your authorized KitchenAid dealer to determine if another warranty applies. If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” you may find additional help by checking the “Assistance or Service” section or by calling KitchenAid. In the U.S.A., call 1-800-422-1230. In Canada, call 1-800-807-6777. 9/07
Keep this book and your sales slip together for future reference. You must provide proof of purchase or installation date for in-warranty service. Write down the following information about your major appliance to better help you obtain assistance or service if you ever need it. You will need to know your complete model number and serial number. You can find this information on the model and serial number label located on the product.
Les utilisateurs et notre équipe répondent généralement sous 24 h — et votre question servira aussi aux suivants.
Soyez le premier à poser une question — d'autres utilisateurs ou notre équipe y répondront.